数控机床m代码含义.docx

1、数控机床m代码含义M00 程序停;M00 Programmable stop;M01 程序选择停 ;M01 Selective programmable stop;M03 主轴顺时针转 ;M03 Rotate spindle clockwise;M04 主轴逆时针转 ;M04 Rotate spindle counterclockwise;M05 主轴停;M05 Spindle stop;M06 换刀*;M06 Tool change Start *;M09 切削液关（所有）;M09 Coolant off (all coolants;M10 B轴夹紧;M10 Clamp B-axis;M11

2、 B轴松开;M11 Unclamp B-axis;M12 Start pallet change *;M12 托盘交换*;M20 A轴夹紧;M20 Clamp A-axis;M21 A轴松开;M21 Unclamp A-axis;M51 变量：穿过主轴冷却液;M51 VARIANT: High pressure coolant through spindle;M52 变量：淋浴冷却液;M52 VARIANT: Coolant shower;M53 VARIANT: Air through spindle on (on I y when minimum quantity lubricationM

3、53 变量：穿过主轴空气开（只有当最小量润滑时）;M54 VARIANT: Minimum quantity lubrication onM54 最小量润滑开;M55 穿过主轴冷却液监控开;M55 VARIANT: High pressure coolant monitoring on;M56 穿过主轴冷却液监控关;M56 VARIANT: High pressure coolant monitoring offM57 选择：过程测量开;M57 OPTION: In process measuring onM58 选择：过程测量关;M58 OPTION: In process measurin

4、g off;M59 设定工件？;M59 Set part is machined;M61 托盘 夹紧*;M61 Clamp pallet *;M62 托盘 松开*;M62 Unclamp pallet *;M65 钻空检查*;M65 OPTION check drill *;M69 托盘交换完成*;M69 Pallet change finished *;M71 换刀门关闭;M71 Close tool change door;M72 换刀门打开;M72 Open tool change door;M75 钻头断刀控制: 检查立刻放下刀具？;M75 OPTION drill break con

5、trol: check lay down tool immediately;M76 刀具断刀控制: 检查被标记的刀具？;M76 OPTION tool break control: check tool of marked place *;M77 刀具断刀控制:放下刀具时在刀库区作标记;M77 OPTION tool break control: mark magazine place of lay down tool *;M78 钻头断刀控制检查*;M78 OPTION check drill break control *;M85 Umspeichermerker Spindel - Ma

6、gazin 1 setzen *;M85 Restore flag spindle - set magazine 1 *;M86 Umspeichermerker Spindel - Magazin 1 ruecksetzen *;M86 Restore flag spindle - reset magazine 1 *;M87 Werkzeugmagazin freigeben von Bearbeitung;M87 Enable tool magazine from machining;M88 装刀启动*;M88 Toolload started *;M89 卸刀启动*;M89 Tool

7、unload started *;M90 装刀 /卸刀 完成*;M90 Toolload I unload finished *;M91 刀具卡爪关闭*;M91 Close tool gripper *;M92 刀具卡爪打开*;M92 Open tool gripper *;M93 主轴紧刀*;M93 Clamp spindle collet *;M94 主轴松刀*;M94 Unclamp spindle collet *;M96 主轴速度监控关*;M96 Spindle speed monitoring off *;M97 主轴速度监控开*;M97 Spindle speed monitor

8、ing on *;M98 打开循环计时器;M98 Start cycle time counter;M99 关闭循环计时器;M99 Stop cycle time counter;M151 选择切削液5bar;M151 OPTION selection coolant 5 bar;M152 选择切削液10bar;M152 OPTION selection coolant 10 bar;M153 选择切削液17bar;M153 OPTION selection coolant 17 bar;M154 选择切削液25bar;M154 OPTION selection coolant 25 bar;

9、M155 选择切削液33bar;M155 OPTION selection coolant 33 bar;M156 选择切削液40bar;M156 OPTION selection coolant 40 bar;M157 选择切削液50bar;M157 OPTION selection coolant 50 bar;M161 VARIANT: Minimum quantity lubrication select pressure step 1M161 最小量润滑选择压力1;M162 VARIANT- Minimum quantity lubrication select pressure s

10、tep 2M162 最小量润滑选择压力2;M163 VARIANT: Minimum quantity lubrication select pressure step 3M163 最小量润滑选择压力3;Erweiterte M-Funktionen XHC 241 SIN 840D ;=;M1=44 以手动断刀检测为条件启动*;M1=44 OPTION: Check start conditions for manual tool break control *;M1=45 以手动断刀检测循环完成*;M1=45 OPTION: Cycle manual tool break control

11、finished *;M1=48 Freigabe Vorrichtung entkuppeln;M1=49 暖机程序完成 *;M1=49 OPTION: Warm-up program finished *;M1=50 托盘交换循环启动*;M1=50 Pallet change cycle started *;M1=51 预先控制托盘夹紧*;M1=51 Precontrol clamp pallet *;M1=52 预先控制托盘放松*;M1=52 Precontrol unclamp pallet *;M1=53 左侧装置冲洗 *;M1=53 PCH rinse lifting device

12、 *;M1=54 Z轴进给启动（相反的程序）*;M1=54 Feed enable Z-axis start from reverse program *;M1=55 Z轴进给停止（相反的程序）*;M1=55 Feed enable Z-axis stop from reverse program *;M1=56 Startvoraussetzung fuer Palettenwechsel fehlt *;M1=56 Start condition for pallet change missing *;M1=57 激活断刀控制*;M1=57 Activate tool break cont

13、rol *;M1=58 在断刀后取消刀具交换;M1=58 Cancel tool change from tool break control *;M1=59 Pruefen ob Altplatz an Wechselstelle *;M1=59 Check if old place at change position *;M1=60 OPTION: Spare for BLUM drill break control laser on *;M1=61 OPTION- Spare for BLUM drill break control laser off *;M1=62 OPTION:

14、Spare for BLUM drill break control open cap *;M1=63 OPTION: Spare for BLUM drill break control close cap *;M1=64 启动主轴切削液;M1=64 Start blow off coolant from spindle;M1=65 停止主轴切削液;M1=65 Stop blow off coolant from spindle;M1=66 REV (Freifahrprogramm NC-Kanal 1 begonnen *;M1=66 REV (reverse program CN-ch

15、annel1 started *;M1=67 REV (Freifahrprogramm NC-Kanal 1 beendet / Reset *;M1=67 REV (reverse program CN-channel1 finished I Reset *;M1=70 主轴短暖机程序激活*;M1=70 Spindle short warm-up cycle is active *;M1=71 主轴短暖机程序循环完成 *;M1=71 Spindle short warm-up cycle finished *;M1=72 主轴长暖机程序激活*;M1=72 Spindle long warm

16、-up cycle is active *;M1=73 主轴长暖机程序循环完成 *;M1=73 Spindle long warm-up cycle finished *;M1=74 主轴暖机程序被低温激活*;M1=74 Spindle warm-up cycle of low temperature is active *;M1=75 主轴暖机程序被低温激活后循环完成 *;M1=75 Spindle warm-up cycle of low temperature finished *;M1=76 机床暖机循环后关闭*;M1=76 OPTION: Machine off from warm-

17、up cycle *;M1=77 开始时间监控器主轴使用10分钟 *;M1=77 Start time monitoring spindle in use 10 minutes *;M1=78 开始时间监控主轴使用15分钟 *;M1=78 Start time monitoring spindle in use 15 minutes *;M1=79 开始时间监控主轴使用60分钟 *;M1=79 Start time monitoring spindle in use 60 minutes *;M1=80 托盘交换请求*;M1=80 Pallet change desired *;M1=81 P

18、CH 使能从暖机循环 *;M1=81 PCH enable from warm-up cycle *;M1=82 暖机循环中主轴倍率100%打开;M1=82 Spindle override 100% on from warm-up cycle *;M1=83 暖机循环中主轴倍率100%关闭;M1=83 Spindle override 100% off from warm-up cycle *;M1=84 暖机循环持续激活;M1=84 Warm-up cycle is still active *;M1=85 开始时间监控主轴使用30分钟 *;M1=85 Start time monitor

19、ing spindle in use 30 minutes *;M1=86 启动主轴装卸刀循环使能*;M1=86 Start enable cycle load I unload tool via spindle *;M1=87 用主轴装刀激活*;M1=87 Load tool active via spindle *;M1=88 用主轴卸刀激活*;M1=88 Unload tool active via spindle *;M1=89 刀库旋转*;M1=89 Rotate tool magazine *;M1=90 刀库在位 *;M1=90 Tool magazine in position

20、 *;M1=91 Altplatz zur Wechselstelle positionieren *;M1=91 Position old place to change position *;M1=92 Startvoraussetzung fuer Werkzeugwechsel fehlt *;M1=92 Start condition for tool change missing *;M1=93 Spindel freigeben fuer Spindel referenzieren *;M1=93 Spindle enable for referencing spindle *;

21、M1=98 Reserviert fuer Maschinendauerlauf mit autom. Werkstueck spannen *;M1=98 Spare for machine continuous cycle with autom. part clamp *;M1=99 Reserviert fuer Maschinendauerlauf mit Palettenwechsel *;M1=99 Spare for machine continuous cycle with pallet change *;M-Funktionen K2 XHC 241 SIN 840D ;=;

22、M64 请求启动监控器在通道2检查钻头;M64 OPTION: Request start enable cycles check drill CN-channel 2 *;M65 在通道2检查钻头*;M65 OPTION: Check drill CN-channel 2 *;M66 Bohrer pruefen beendet NC-Kanal 2 *;M66 OPTION: Check drill finished CN-channel 2 *;M71 Rev-Progr. (Freifahrprogramm NC-Kanal 2 begonnen *;M71 Rev-progr. (r

23、everse program CN-channel 2 started *;M72 Rev-Progr. (Freifahrprogramm NC-Kanal 2 beendet *;M72 Rev-progr. (reverse program CN-channel 2 finished *;M78 监控器在通道2检查钻头*;M78 OPTION: Monitoring start check drill CN-channel 2 *;M91 刀具卡爪关闭*;M91 OPTION: Close tool gripper *;M92 刀具卡爪打开*;M92 OPTION: Open tool gripper *