锂离子电池专业英语.docx

1、锂离子电池专业英语锂离子电池经常使用专业英语（一）序号 首字母 英文 中文1 A aging 老化2 B battery charger 充电器3 black-fleck 黑斑4 C cap 盖板5 capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 charge(capacity) retention 荷电（容量）维持10 checking code 检码11 concave spot 凹点12 constant current charge 恒流充电13 constant curren

2、t discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 纠正方法16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 D dark trace 暗痕20 degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 E Electrical and MechanicalServices Department 机电部26 electrolyte 电解，电解液27 empais

3、tic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 侵蚀32 explosion-proof line 防爆线33 F first inspection 首检34 formation 化成35 fracture 断裂36 I inspection 查验37 insulate 绝缘38 internal resistance 内阻39 J jellyroll 卷芯40 joint 接缝，结合点41 L laser deflecting

4、偏光42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接-平焊laser welding-standing weld 激光焊接-立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51 meet requirement 达到要求52 memo

5、ry effects 经历效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE膜64 pit 坑点65 placing cells into the box 电芯装盒66 point inspection 点检67

6、 preventive measures 预防方法68 pricking the tapes 扎孔69 process inspection 制程查验70 put the battery piled up 将电芯叠放在一路71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量操纵74 quality improvement 质量改良75 quality match 品质配对76 quality planning 质量策划77 R rated capacity 额定容量78 recharge 再充电79

7、refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面，反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜84 S safety vent 安全阀85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smudginess 污物91 spot welding by l

8、aser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压贮存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqual

9、ified products 不合格品104 W wave 波浪105 working procedure 工序（二）盖板 cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage i

10、n discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape

11、点焊spot welding超声焊ultrasonic welding三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing device vacuum mixing device涂布机coating equipment裁纸刀paper knife ,cutting knife分条机equipment for cutting big piece

12、 to much pieces辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery in

13、ner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper锂离子电池设计专业英语Capacity 容量Battery Thickness 电池厚度Battery width 电池宽度Battery length 电池高度Impedance 内阻Can thickness 壳体厚度Can wall thickness 壳体壁厚Can bottom thikness 壳体底部厚度Can lid thickness 壳体盖板

14、厚度PP film thickness PP胶厚度Ni (AL) tab thickness Ni（Al）极耳厚度Battery width 电池宽度Can width margin 电池宽度留边Can length 壳体长度Can cross area 壳体体积Winding pin width 卷针宽度Can Side residue 壳边残余Naked battery thickness 裸漏电池厚度Naked battery width 裸漏电池宽度Naked battery length 裸漏电池高度Cathode formulation 阴极含量Cathode material s

15、pecific capacity 阴极克比容量Cathode 阴极装填Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode weight 阴极重量Cathode thickness 阴极厚度Cathode elongation rate 延伸率Cathode actual length 阴极实际长度Cathode design length 阴极设计长度Cathode width 阴极宽度Cathode Scratched area width 阴极涂片宽度Al foil density 铝箔密度Al foil thickne

16、ss 铝箔厚度Cathode weight 阴极重量Separator thickness 隔离膜厚度Separator length 隔离膜长度Separator width 隔离膜宽度Separator density 隔离膜密度Separator weight 隔离膜重量Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode loading 阳极装填量Anode area density 阳极面密度Anode bulk density 阳极体积密度Anode thickness 阳极厚度Anode length

17、阳极长度Anode width 阳极宽度Anode scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度Anode weight 阳极重量Cathode Tab length 阴极极耳长Cathode Tab width 阴极极耳宽Cathode Tab thickness 阴极极耳厚度Anode Tab length 阳极极耳长度Anode Tab width 阳极极耳宽度Anode Tab thickness 阳极极耳厚度Adhesive tape Length 胶带长度Adhesive tape Wi

18、dth 胶带宽度Adhesive tape thickness 胶带厚度Assembly adhesive tape 装配胶带Bottom length 底部长度Bottom Width 底部宽度Bottom Thickness 底部厚度Top length 顶部长度Top Width 顶部宽度Top Thickness 顶部厚度Welding length 焊接长度Welding Width 焊接宽度Welding Thickness 焊接厚度Electrolyte 电解液Battery Impedance 电心内阻Battery weight 电池重量Can wall thickness

19、壳体壁厚Can bottom thikness 壳体底厚Can lid thickness 盖板厚度Can width margin 壳体边缘宽度Can Side residue 壳体留边Cathode formulation 阴极含量Cathode material specific capacity 阴极克容量Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode elongation rate 阴极延伸率Cathode scratched area width/Pin width 阴极刮粉宽Al foil density 铝箔密度Al foil thickness 铝箔厚度Separator thickness 隔离膜厚度Separator density 隔离膜密度Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode bulk density 阳极体积密度Anode Scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度