海洋石油常用中英文对照词汇.docx

1、海洋石油常用中英文对照词汇AA-60 fire door A-60级防火门a-hundred-year return period 百年一遇abrasive （喷砂用的）磨料abrasive paper 砂纸AC generator 交流发电机AC motor 交流电动机accelerated corrosion testing 加速腐蚀试验acceptance criteria 合格准则access hole (for welding) = cope hole (焊接)工艺孔accommodation and power platform (APP) 生活动力平台according to =

2、 in accordance with =in line with = as per = in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥additive 添加剂adhere to 遵守（动词）adherence to 遵守（名词）adjacent columns 相邻立柱adverse combination of loads 载荷的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for con

3、struction) 建造批准aforementioned 上述aft winch 船艉绞车agitator 搅拌器air blower 鼓风机air compressor 空气压缩机air driven pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验air-hose 风带aircraft obstruction beacon 航空障碍灯alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨脂漆allowable (working) stress 许用应力

4、Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮ambient air temperature 环境气温ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺栓anchor ground 锚地anchor pile 锚桩anchor profile/pattern 涂装表面的粗糙度anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射

5、角angle probe method 超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anode resistance 阳极电阻anti-electrostatic floor 防静电地板anticorrosive paint 防锈漆antipollution measures 防污染措施API specified requirements API规定

6、的要求apparent batter 视斜度applicable API specification API适用规范approach-departure sector 直升飞机起落扇形区appurtenance = attachment= accessory= auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system 铰接塔系泊系统artificial island

7、 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-rolled 轧制状态assemble 组装（动词）assembly 组装（动词）associated gas 伴生气at the option of A 按A的意愿atmospheric diving system= unpressurized diving system 常压潜水系统atmospheric vent 放空管attachment 附件auto fire alarm system 火灾自动报警系统automatic spraying syste

8、m 自动喷淋系统B(to be) buttered (焊接的)长肉back chipping 清根back gouging 反面气刨backing weld 打底焊道backpressure regulator (self contained) 背压式调节阀（自力式）backwash return pump 反冲洗回流泵backwash surge tank 反冲洗罐Ball hardness 布氏硬度ball valve 球阀bar （截面较小的）圆钢 方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船

9、强度及稳性barrel （管件的）加厚段base metal 母材、基本金属basic design 基本设计basic electrode = lime type covered electrode 碱性焊条battery room 蓄电池间blowout preventer system (BOP system) 防喷器系统beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前bending mo

10、ment 弯矩bending stress 弯曲应力bevel 开坡口bid drawing 坡口bevel angle 坡口面角度beveling / chamfering 招标图纸bilge / fire pump 舱底污水-消防两用泵bilge alarm system 污水报警系统bid / tender for 投标blast cleaning 喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow count 打桩的锤击数blowdown vessel 排放罐blowhole; gas pore 气孔blowout prevente

11、r stack 防喷器组buoyant turret mooring 浮筒转塔式系泊boat landing 登船平台bolt, nut and washer 螺栓、螺母及垫片bolted connection 螺栓连接boom 吊机扒杆boom angle 吊机倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船boundary condition 边界条件bow 船艏box beam 箱形梁box type joint 箱形节点brace 拉筋bracelet

12、 anode 手镯式阳极branch member 支杆breathing apparatus , respirator 防毒面具bridge 栈桥bridge (overhead) crane 天车吊brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带bulb angle 球扁钢build-up girder 组合梁bulk head 隔板、舱壁burn through 烧穿burner 气焊工burr and flashing 飞边毛刺business and management 经营管理butt-welded seam 对接焊缝butt

13、erfly valve 蝶阀Ccable layer 敷缆船cable rack / tray 电缆托架caisson 沉箱caisson washing pump 洗舱泵caisson-type platform 沉箱式平台can （管件的）段cantilever beam 悬臂梁cantilever jack-up rig 悬臂自升式钻井船cantilever well module 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment = overturn moment 倾覆力矩carbon arc

14、 air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon-dioxide(CO2) arc welding 二氧化碳气体 保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机carrier （搬运）小车carry out = perform = conduct = execute 进行、执行catenary anchor leg mooring (CALM) 悬链锚腿系泊cathodic protection 阴极保护cella

15、r deck 底甲板cellar shutdown panel (CSDP) 井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room (CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵centrifuger 离心机ceramic fibres 防火陶棉cera

16、mic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链chair with arm-rest 带扶手的半软椅chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击试验chart datum 海图基准面check randomly 抽检check valve 止回阀checkered plate 花纹板chemical injection package 化学注入撬chemical injection sy

17、stem 化学注入系统chemical seal 化学密封chipping hammer 敲渣锤chisel 风铲chord member 弦杆christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐clearance 间隙client 业主、顾客close drain tank 闭式排放罐closed / open circuit 闭 / 开路closed dra

18、in pump 闭式排放泵clustered well heads 丛式井口CO2 cylinder unit CO2气瓶组CO2 extinguisher CO2灭火器coal tar epoxy paint 含焦油环氧涂料coaming 挡水扁铁coating 涂装coating interval 涂漆间隔coefficient 系数cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工、冷作collapse ring 加强环板column 立柱combustible gas detector 可燃气体探测器come-along 手扳葫芦commerci

19、al blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document 编制和保存文件complete penetration groove weld 全熔透坡口焊completion riser 完井立管complex joint 复杂节点compliance with 符合（名词）comply with 符合（动词）composite rockwool ceiling 复合岩棉天花板composite rockwool panel 复合岩棉板concentric reducer 同心大小头conceptual des

20、ign 概念设计concrete platform 混凝土平台condensate drum 冷凝液罐condensing water 冷凝水conductor 隔水套管conductor guide 套管导向cone 大小口、锥体conform to = stick to = adhere to 符合、遵守connection 节点、连接consumption rate 阳极消耗率continuous beam 连续梁continuous double fillet weld 双面连续贴角焊continuous welding 连续焊contract 合同contraction stress

21、 收缩应力contractor 承包商control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole (焊接)工艺孔corrective and preventive action 纠正和预防措施correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀挂片corrosion protection 防腐corrugated plate interceptor 斜板

22、分离器couplant UT用的耦合剂coupling 联轴器、管箍crack 裂纹crane barge, crane vessel 起重船crane support 吊机支撑crater 焊口crawler crane 履带吊车criteria (验收)标准cross angle 交叉角cross section 横截面crow bar 撬杠cruciform bollard 单十字带缆柱crude cooler 原油冷却器crude filter 原油过滤器crude heat exchanger 原油换热器crude loading /export pump 原油外输泵crude lo

23、ading pump 原油装载泵crude oil drain tank 原油排放舱crude preheat exchanger 原油预热器crude suction strainer 原油吸入滤器crude transfer 原油输送泵cup support 垫墩curing time （油漆的）固化时间current capacity （阳极的）电流容量current density （阳极的）电流密度current direction 海流方向curvature radius 曲率半径customer 客户cut by torch 以火焰切割cut off 割除、割除物cutoff a

24、llowance 切割裕量cutting plan 排板图cutting sheet 单件图D(in) duplicate 一式两份(to) drive piles 打桩DAC curves 距离-振幅曲线daily diesel filter 日用柴油滤器damage-prone connection 易破坏的节点damper, dampener 减震器DC generator 直流发电机Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊车deck water seal unit 甲板水封装置deep freeze compre

25、ssor 深冷压缩机deepwater jacket 深水导管架defect /default /disconnection 缺陷deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater 脱水预热器dehydration feed pump 电脱水供给泵delivery of materials 材料交货derrick barge 回转式起重船desander 除砂罐design basis 设计基准design parameters 设计参数detail 详图detail design 详细设计develop /

26、 establish a document 编制文件dew point 露点DFT (dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表diaphragm 隔板diaphragm valve 隔膜阀die stamp 钢印diesel daily tank 柴油日用罐diesel filter coalescer 柴油过滤净化装置diesel generator set 柴油发电机组diesel oil daily tank with heater 柴油日用罐（带加热器）diesel pump 柴油泵diesel storage t

27、ank 柴油储罐diesel storage tank with heater 柴油储罐（带加热器）diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀diffuser 布风气dihedral angle 二面角dimensional checks 尺寸检查direct / alternating current arc welding 直/交流电弧焊direct current emergency supply 直流应急电源disassembling 拆除discontinuity

28、 缺陷displacement oil tank 置换油罐distortion from welding 焊接变形distress signals 遇险呼救信号diver 潜水员diver support vessel 潜水作业船document approval and issue 文件的批准和下发documentation 文件编制dog 组装用的刀把dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bed 双层床double bevel groove k形坡口double bollard

29、 双柱带缆桩double groove 双面坡口double probe method 双探头法double V groove 双面V形坡口(X形)doubler plate 垫板、包板down hill welding 向下焊drain pit 排放池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类图纸种类有：conceptual drawing 概念图纸basic drawing 基本设计图纸bid drawing 招标图纸design drawing 详细设计图纸fabrication drawi

30、ng 加工设计图纸shop drawing 车间加工图纸as-built drawing 完工图dredger 挖泥船drift pin 心轴、销子drift test 管流试验、管线试通drill 钻头drilling module 钻井模块drilling platform 钻井平台drilling template 钻井基盘drillship, drilling ship 浮式钻井船driving voltage 驱动电压dry chemical extinguisher 干粉灭火器dry-type tree 干式采油树dryer 烘箱during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection 着色检验dynamic-positioning rig 动力定位钻井船EEarth le