理光复印机维修代码故障代码.docx

1、理光复印机维修代码故障代码理光复印机维修代码故障代码2009-05-08 20:52:04| 分类: 默认分类 | 标签: |字号大中小 订阅 一:如何进入 SP 模式 1. 按以下次序按动面键 C ? 1 ? 0 ? 7 ? C ，保持按 C/ ?键 3 秒以上; 2. SP 模式菜单显示在 LCD 上， 1 COPY 2 FAX 3 PRINTER 3. 按你需要选定模式号码。 二:如何退出 SP 模式 1. 按 C 或 CANCEL 键一次或二次以上来返回到待机模式显示为止 三:从 SP 模式进入复印模式 , 按 COPY 键，选择适当的复印模式，并试复印品;要返回 SP 模式，按 C

2、键。 四:如何选择程序号 , 用数字键输入第一级别程序号码(或用右或左光标键改变号码)，并按 # 或 OK 键 , 用数字键输入第二级别程序号码(或用右或左光标键改变号码)，并按 # 或 OK 键 , 若选择第三级别程序号码(如果有):选择第二级别，然后使用右或左光标键。 , 要返回到下一个更高级别，按 C 。 五:对 SP 模式输入一个数值或设定值 , 首先进入所要的程序号; , 使用数字键，进入所要求的设定值，进入所要求的设定值之前，如有必要，使用? /* 键在“ + ”和“ - ”之间变换，然后按 R/# 键或 OK 键盘。 六:常用SP 模式代码 理光复印机1015/1018常用的SP

3、模式代码 1. 更换铁粉后 TD 传感器初始化SP模式代码: SP2-214; 2. 装新机最后要用 SP7-825 初始化电气总计数器; 3. 如何清除 PM 计数:进入 SP7-804，同时按原稿类型键和 OK 或 R/# 键来复位计数器，成功则显示“执行完成”; 4. 要测试、制做纯黑打印品，使用 SP5-902; 用手送纸复印的复印件不完整，如何解决, 先选到手送纸盒，然后按“ # ”键，这时会出现纸盒尺寸，挑选 A4 尺寸，复印机一张，如果好，手送传感器坏。 怎么调节定影辊压力? and special tools for emergency response equipment a

4、nd facilities. Emergency preparedness and response plan 1) emergency response (1) If a major accident occurs, the project should set up emergency response teams, chaired by the project manager, head of production and safety coordinators, professional foreman for the crew, primarily responsible for t

5、he orderly rescue when an emergency occurs or processing, outsourcing, team manager and support staff, assisting the Deputy Project Manager for related auxiliary work. (2) after the accident, the project manager is responsible for field commander, advance the establishment of emergency response team

6、 personnel, accountability, seriously injured officers sent out rescue, have procedures to deal with accidents, incidents, maximum reduction in casualties and property loss. (3) If an accident occurs, press Division in advance for emergency personnel cleared, concentrate manpower and material and fi

7、nancial resources to rescue the injured, decrease of the maximum loss. (4) after the accident processing work (5) identified the cause of the accident and the person responsible. (6) the written report to the supervisor in writing, including the time and place of the accident, injury (death) persons

8、 name, sex, age, trades, injuries, injuries. (7) the development of effective preventive measures to prevent such accidents from happening again. (8) education of all personnel of the organization. (9) informed criticism of those responsible. (10) all personnel read out the results, and responsible

9、disposal. (11) maintenance of emergency supplies, maintenance and testing ? strengthening the day-to-day management of the various fire fighting equipment fire-fighting equipment, authorities should be staffed, equipped with fire extinguishers. Fire hydrants identified person responsible for regular

10、ly inspecting, testing, at any time in good condition. ? Guard monthly check-fire extinguishers and fire-fighting equipment. ? once every quarter, inspections and tests of a fire hydrant in good condition. 2), plans to develop (1) casualties occurred in construction, such as accidents or accidents o

11、f the direct economic 在手送纸盘上放置 OHP 纸，进入 SP1-109 ，按 COPY 键，机器把纸送到定影部分停留 20 秒，然后把它排出，检查排出的 OHP 纸的压印是否前后一样，不一样可改变弹簧钩子的位置，较高的钩子位置可产生较大的拉力 型号:松下7713,7813复印机 现象:复印件左右两端有较宽的黑带，放大缩小会有变化。 故障:光学系统脏或曝光灯罩遮光调节片松动。 处理方法:清洁光学系统及调节遮光片。 型号:理光3813,4615,4015复印机 现象:复印件底灰太重。 故障:光学系统太脏。 处理方法:清洁光学系统。 型号:理光3813,4615,4015复印

12、机 现象:复印件复印第二面时出现严重皱纸。 故障:定影进纸导板堆积硬化碳粉太多，凹凸不平。 处理方法:打开定影组件，清除堆积物。 型号:理光3813,4615,4015复印机 现象:严重漏碳粉和载体，复印件有堆积黑块，印品黑白不分。 故障:回收粉仓严重堵塞，回收螺旋杆无法回收废碳粉。 处理方法:回收粉仓传动不灵活，或湿气太重，废粉无法回收。 型号:理光1015,1018数码复印机 现象:开机显示SC541，定影恒温电阻开路，恢复后开机仍显示。 故障:该代码为A级代码必须进入维修模式进行手动复位。 处理方法:进入维修模式:复位键,107,停止键，SP5-810-1原稿方式键+#号键进行代码复位。

13、 型号:理光200数码复印机 现象:打印正常，复印无图象。 故障:扫描部分故障，数据线脱落。 处理方法:重新装上。 型号:松下7713,7813复印机 现象:开机显E310高压漏电，但充电和转分无漏电现象。 and special tools for emergency response equipment and facilities. Emergency preparedness and response plan 1) emergency response (1) If a major accident occurs, the project should set up emergenc

14、y response teams, chaired by the project manager, head of production and safety coordinators, professional foreman for the crew, primarily responsible for the orderly rescue when an emergency occurs or processing, outsourcing, team manager and support staff, assisting the Deputy Project Manager for

15、related auxiliary work. (2) after the accident, the project manager is responsible for field commander, advance the establishment of emergency response team personnel, accountability, seriously injured officers sent out rescue, have procedures to deal with accidents, incidents, maximum reduction in

16、casualties and property loss. (3) If an accident occurs, press Division in advance for emergency personnel cleared, concentrate manpower and material and financial resources to rescue the injured, decrease of the maximum loss. (4) after the accident processing work (5) identified the cause of the ac

17、cident and the person responsible. (6) the written report to the supervisor in writing, including the time and place of the accident, injury (death) persons name, sex, age, trades, injuries, injuries. (7) the development of effective preventive measures to prevent such accidents from happening again

18、. (8) education of all personnel of the organization. (9) informed criticism of those responsible. (10) all personnel read out the results, and responsible disposal. (11) maintenance of emergency supplies, maintenance and testing ? strengthening the day-to-day management of the various fire fighting

19、 equipment fire-fighting equipment, authorities should be staffed, equipped with fire extinguishers. Fire hydrants identified person responsible for regularly inspecting, testing, at any time in good condition. ? Guard monthly check-fire extinguishers and fire-fighting equipment. ? once every quarte

20、r, inspections and tests of a fire hydrant in good condition. 2), plans to develop (1) casualties occurred in construction, such as accidents or accidents of the direct economic 故障:由于误*作维修，右端刮板固定镙钉绝缘层被镙钉刺穿与充电座端子之间接触。 处理方法:更换短镙丝钉，进行绝缘处理。 型号:松下7713,7813复印机 现象:复印全黑印品时有白条，正常复印时出现白条处字体全无。 故障:充电座和转分座电极丝脏。

21、 处理方法:清洁电极丝或更换充电及转分座。 型号:理光180复印机 现象:无卡纸显卡纸。 故障:定影支架松脱造成定影传感器连动杆不能正常复位。 处理方法:紧固定影支架或更换定影支架。 型号:松下7713,7813复印机 现象:定影处卡纸，定影装置不运行。 故障:定影传动齿轮与电机主动齿轮之间啮合错位打滑。 处理方法:重新关好左端盖，更换已坏的齿轮。 型号:理光1015,1018数码复印机 现象:打印时出乱码，并且不停止。 故障:计算机*作系统出错或驱动程序安装出错。 处理方法:重新安装驱动和*作系统。 型号:松下7718/7722/7735复印机 现象:开机预热后现E102倍率调整错误。 故障

22、:第四，第五反光镜脱位，调整错误。 处理方法:重新安装，调整第四，第五反光镜。 型号:理光1022数码复印机 现象:复印件有黑线。 故障:光学部分脏。 处理方法:清洁光学部分，放大和缩小复印后黑条消失。 型号:理光200数码复印机 现象:出现SC542维修呼叫，定影出错。 故障:使用时间过长出现高温异常。 and special tools for emergency response equipment and facilities. Emergency preparedness and response plan 1) emergency response (1) If a major a

23、ccident occurs, the project should set up emergency response teams, chaired by the project manager, head of production and safety coordinators, professional foreman for the crew, primarily responsible for the orderly rescue when an emergency occurs or processing, outsourcing, team manager and suppor

24、t staff, assisting the Deputy Project Manager for related auxiliary work. (2) after the accident, the project manager is responsible for field commander, advance the establishment of emergency response team personnel, accountability, seriously injured officers sent out rescue, have procedures to dea

25、l with accidents, incidents, maximum reduction in casualties and property loss. (3) If an accident occurs, press Division in advance for emergency personnel cleared, concentrate manpower and material and financial resources to rescue the injured, decrease of the maximum loss. (4) after the accident

26、processing work (5) identified the cause of the accident and the person responsible. (6) the written report to the supervisor in writing, including the time and place of the accident, injury (death) persons name, sex, age, trades, injuries, injuries. (7) the development of effective preventive measu

27、res to prevent such accidents from happening again. (8) education of all personnel of the organization. (9) informed criticism of those responsible. (10) all personnel read out the results, and responsible disposal. (11) maintenance of emergency supplies, maintenance and testing ? strengthening the

28、day-to-day management of the various fire fighting equipment fire-fighting equipment, authorities should be staffed, equipped with fire extinguishers. Fire hydrants identified person responsible for regularly inspecting, testing, at any time in good condition. ? Guard monthly check-fire extinguisher

29、s and fire-fighting equipment. ? once every quarter, inspections and tests of a fire hydrant in good condition. 2), plans to develop (1) casualties occurred in construction, such as accidents or accidents of the direct economic 处理方法:进入SP模式:复位键-107-停止键;复位SC代码:5-810-1原稿方式键+#号键进行代码复位。 型号:理光200数码复印机 现象:

30、显SC401转印辊漏电，更换转印辊无效。 故障:鼓组件损坏漏载体与转印辊之间漏电。 处理方法:维修或更换鼓组件。 型号:理光270数码复印机 现象:开机和每次启动复印时，噪声特大。 故障:激光电机不良。 处理方法:拆开激光电机在电机轴上打油或更换激光电机。 型号:理光1015,1018数码复印机 现象:图象淡或半边浓半边淡。 故障:激光单元六棱镜脏。 处理方法:清洁六棱镜。 型号:松下7718/7722/7735复印机 现象:出现载体到期维修呼叫，而停机无法复印。 故障:由于载体到期，复印到限张数被锁死。 处理方法:更换好载体。1、进入维修模式:(USER键+A3键+3);2、进行计数器清零:

31、(F7-C99-复印键);3、进行维修呼叫复位:(F5-7O-复印键);4进行载体初始化:(F8-C09-复印键) 型号:理光1015,1018数码复印机 现象:开机出现SC194维修呼叫，白板检测出错。复印时无法复位复印第二张稿纸时会复印第一张的复印件。 故障:光学系统脏。 处理方法:清洁光学部分。 型号:理光200数码复印机 现象:复印件有重影。 故障:热辊脏表面脏。 处理方法:清洁热辊。 型号:理光1022数码复印机 现象:16K、B4、8K不能双面复印。 故障:复印机不支持特殊纸双面复印。 and special tools for emergency response equipme

32、nt and facilities. Emergency preparedness and response plan 1) emergency response (1) If a major accident occurs, the project should set up emergency response teams, chaired by the project manager, head of production and safety coordinators, professional foreman for the crew, primarily responsible for the orderly rescue when an emergency occurs or processing, outsourcing, team manager and support staff, assisting the Deputy Project Manager for related auxilia