新CCNA题库word版1100题.docx

1、新CCNA题库word版1100题QUESTION 1When you are logged into a switch, which prompt indicates that you are in privileged mode?A. %B. C. D. $E. #QUESTION 2Which command shows system hardware and software version information?A. show configurationB. show environmentC. show inventoryD. show platformE. show versi

2、onQUESTION 3Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802. 1Qtrunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 thenative VLAN is not specified.What will happen in this scenario?A. 802.1Q giants frames cou

3、ld saturate the link.B. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.C. A native VLAN mismatch error message will appear.D. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.QUESTION 4Which command would correctly configure a serial port on a router with the last usable host

4、 address in the192.216.32.32/29 subnet?A. Router(config-if)# ip address 192.216.32.38 255.255.255.240B. Router(config-if)# ip address 192.216.32.39 255.255.255.224C. Router(config-if)# ip address 192.216.32.63 255.255.255.248D. Router(config-if)# ip address 192.216.32.39 255.255.255.248E. Router(con

5、fig-if)# ip address 192.216.32.63 255.255.255.248F. Router(config-if)# ip address 192.216.32.38 255.255.255.248QUESTION 5The network default gateway applying to a host by DHCP is 192.168.5.33/28. Which option is the valid IPaddress of this host?A. 192.168.5.55B. 192.168.5.47C. 192.168.5.40D. 192.168

6、.5.32E. 192.168.5.14QUESTION 6Which two addresses can be assigned to a host with a subnet mask of 255.255.254.0? (Choose two.)A. 113.10.4.0B. 186.54.3.0C. 175.33.3.255D. 26.35.2.255E. 17.35.36.0QUESTION 7The network administrator has asked you to check the status of the workstations IP stack by ping

7、ing theloopback address. Which address would you ping to perform this task?A. 10.1.1.1B. 127.0.0.1C. 192.168.0.1D. 239.1.1.1QUESTION 8Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an IPaddress of 192.0.2.100/28. The two workstations are connected wit

8、h a straight-through cable. Attempts toping between the hosts are unsuccessful. What two things can be done to allow communications betweenthe hosts? (Choose two.)A. Replace the straight-through cable with a crossover cable.B. Change the subnet mask of the hosts to /25.C. Change the subnet mask of t

9、he hosts to /26.D. Change the address of Workstation A to 192.0.2.15.E. Change the address of Workstation B to 192.0.2.111.QUESTION 9Your ISP has given you the address 223.5.14.6/29 to assign to your routers interface. They have alsogiven you the default gateway address of 223.5.14.7. After you have

10、 configured the address, the router isunable to ping any remote devices. What is preventing the router from pinging remote devices?A. The default gateway is not an address on this subnet.B. The default gateway is the broadcast address for this subnet.C. The IP address is the broadcast address for th

11、is subnet.D. The IP address is an invalid class D multicast address.QUESTION 10Which command is used to copy the configuration from RAM into NVRAM?A. copy running-config startup-configB. copy startup-config: running-config:C. copy running config startup configD. copy startup config running configE.

12、write terminalQUESTION 11Which command is used to load a configuration from a TFTP server and merge the configuration intoRAM?A. copy running-config: TFTP:B. copy TFTP: running-configC. copy TFTP: startup-configD. copy startup-config: TFTP:QUESTION 12A system administrator types the command to chang

13、e the hostname of a router. Where on the Cisco IFS isthat change stored?A. NVRAMB. RAMC. FLASHD. ROME. PCMCIAQUESTION 13Which command is used to configure a default route?A. ip route 172.16.1.0 255.255.255.0 0.0.0.0B. ip route 172.16.1.0 255.255.255.0 172.16.2.1C. ip route 0.0.0.0 255.255.255.0 172.

14、16.2.1D. ip route 0.0.0.0 0.0.0.0 172.16.2.1QUESTION 14If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?(Choose two.)A. ip default-gateway 0.0.0.0B. ip route 172.16.2.1 0.0.0.0 0.0.0.0C. ip default-network 0.0.0.0D. ip default-route 0.0.0.0 0.0.0.0 1

15、72.16.2.1E. ip route 0.0.0.0 0.0.0.0 172.16.2.1QUESTION 15Which command would you configure globally on a Cisco router that would allow you to view directlyconnected Cisco devices?A. enable cdpB. cdp enableC. cdp runD. run cdpQUESTION 16Which command is used to see the path taken by packets across a

16、n IP network?A. show ip routeB. show routeC. tracerouteD. trace ip routeQUESTION 17Which command is used to debug a ping command?A. debug icmpB. debug ip icmpC. debug tcpD. debug packetQUESTION 18Which command displays CPU utilization?A. show protocolsB. show processC. show systemD. show versionQUES

17、TION 19When configuring a serial interface on a router, what is the default encapsulation?A. atm-dxiB. frame-relayC. hdlcD. lapbE. pppQUESTION 20What must be set correctly when configuring a serial interface so that higher-level protocols calculate thebest route?A. bandwidthB. delayC. loadD. reliabi

18、lityQUESTION 21A company implements video conferencing over IP on their Ethernet LAN. The users notice that thenetwork slows down, and the video either stutters or fails completely. What is the most likely reason forthis?A. minimum cell rate (MCR)B. quality of service (QoS)C. modulationD. packet swi

19、tching exchange (PSE)E. reliable transport protocol (RTP)QUESTION 22Which layer in the OSI reference model is responsible for determining the availability of the receivingprogram and checking to see if enough resources exist for that communication?A. transportB. networkC. presentationD. sessionE. ap

20、plicationQUESTION 23Data transfer is slow between the source and destination. The quality of service requested by the transportlayer in the OSI reference model is not being maintained. To fix this issue, at which layer should thetroubleshooting process begin?A. presentationB. sessionC. transportD. n

21、etworkE. physicalQUESTION 24Which protocols are found in the network layer of the OSI reference model and are responsible for pathdetermination and traffic switching?A. LANB. routingC. WAND. networkQUESTION 25Which command reveals the last method used to powercycle a router?A. show reloadB. show boo

22、tC. show running-configD. show versionQUESTION 26Which three options are valid WAN connectivity methods? (Choose three.)A. PPPB. WAPC. HDLCD. MPLSE. L2TPv3CCNA考试报名1700元 7F. ATMQUESTION 27Refer to the exhibit. Which WAN protocol is being used?A. ATMB. HDLCC. Frame RelayD. PPPQUESTION 28What is the di

23、fference between a CSU/DSU and a modem?A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signalsfrom a router to a leased line.B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signalsfrom a router to a leased line

24、.C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signalsfrom a router to a phone line.D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signalsfrom a router to a phone line.QUESTION 29A network administrator mu

25、st configure 200 switch ports to accept traffic from only the currently attachedCCNA考试报名1700元 8host devices. What would be the most efficient way to configure MAC-level security on all these ports?A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port secur

26、itymac-address command.B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port securitymac-address command.C. Use the switchport port-security MAC address sticky command on all the switch ports that have enddevices connected to them.D. Use show mac-address-tab

27、le to determine the addresses that are associated with each port and thenenter the commands on each switch for MAC address port-security.QUESTION 30When troubleshooting a Frame Relay connection, what is the first step when performing a loopback test?A. Set the encapsulation of the interface to HDLC.

28、B. Place the CSU/DSU in local-loop mode.C. Enable local-loop mode on the DCE Frame Relay router.D. Verify that the encapsulation is set to Frame Relay.What occurs on a Frame Relay network when the CIR is exceeded?A. All TCP traffic is marked discard eligible.B. All UDP traffic is marked discard elig

29、ible and a BECN is sent.C. All TCP traffic is marked discard eligible and a BECN is sent.D. All traffic exceeding the CIR is marked discard eligible.QUESTION 32What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)A. They create split-horizon issues.B. They require a

30、 unique subnet within a routing domain.C. They emulate leased lines.D. They are ideal for full-mesh topologies.E. They require the use of NBMA options when using OSPF.QUESTION 33Refer to the exhibit. Addresses within the range 10.10.10.0/24 are not being translated to the 1.128.0/16range. Which comm

31、and shows if 10.10.10.0/24 are allowed inside addresses?A. debug ip natB. show access-listC. show ip nat translationD. show ip nat statisticsQUESTION 34A wireless client cannot connect to an 802.11b/g BSS with a b/g wireless card. The client section of theaccess point does not list any active WLAN clients. What is a possible reason for this?A. The incorrect channel is configured on the client.B. The clients IP address is on the wrong subnet.C. The client has an incorrect pre-shared key.