1、CISCO路由器产品配置手册二PSTNPSTN 电话网络(PSTN)是目前普及程度最高、成本最低的公用通讯网络,它在网络互连中也有广泛的应用。电话网络的应用一般可分为两种类型,一种是同等级别机构之间以按需拨号(DDR)的方式实现互连,一种是ISP为拨号上网为用户提供的远程访问服务的功能。 1. 远程访问 1.1. Access Server基本设置: 选用Cisco2511作为访问服务器,采用IP地址池动态分配地址.远程工作站使用WIN95拨号网络实现连接。 全局设置: 任务 命令 设置用户名和密码 username username password password 设置用户的IP地址池
2、ip local pool default | pool-name low-ip-address high-ip-address 指定地址池的工作方式 ip address-pool dhcp-proxy-client | local 基本接口设置命令: 任务 命令 设置封装形式为PPP encapsulation ppp 启动异步口的路由功能 async default routing 设置异步口的PPP工作方式 async mode dedicated | interactive 设置用户的IP地址 peer default ip address ip-address | dhcp | p
3、ool pool-name 设置IP地址与Ethernet0相同 ip unnumbered ethernet0 line拨号线设置: 任务 命令 设置modem的工作方式 modem inout|dialin 自动配置modem类型 modem autoconfig discovery 设置拨号线的通讯速率 speed speed 设置通讯线路的流控方式 flowcontrol none | software lock in | out | hardware in | out 连通后自动执行命令 autocommand command 访问服务器设置如下: Router: hostname
4、Router enable secret 5 $1$EFqU$tYLJLrynNUKzE4bx6fmH/ ! interface Ethernet0 ip address 10.111.4.20 255.255.255.0 ! interface Async1 ip unnumbered Ethernet0 encapsulation ppp keepalive 10 async mode interactive peer default ip address pool Cisco2511-Group-142 ! ip local pool Cisco2511-Group-142 10.111
5、.4.21 10.111.4.36 ! line con 0 exec-timeout 0 0 password cisco ! line 1 16 modem InOut modem autoconfigure discovery flowcontrol hardware ! line aux 0 transport input all line vty 0 4 password cisco ! end 相关调试命令: show interface show line 1.2. Access Server通过Tacacs服务器实现安全认证: 使用一台WINDOWS NT服务器作为Tacacs
6、服务器,地址为10.111.4.2,运行Cisco2511随机带的Easy ACS 1.0软件实现用户认证功能. 相关设置: 任务 命令 激活AAA访问控制 aaa new-model 用户登录时默认起用Tacacs+做AAA认证 aaa authentication login default tacacs+ 列表名为no_tacacs使用ENABLE口令做认证 aaa authentication login no_tacacs enable 在运行PPP的串行线上采用Tacacs+做认证 aaa authentication ppp default tacacs+ 由TACACS+服务器
7、授权运行EXEC aaa authorization exec tacacs+ 由TACACS+服务器授权与网络相关的服务请求。 aaa authorization network tacacs+ 为EXEC会话运行记帐.进程开始和结束时发通告给TACACS+服务器。 aaa accounting exec start-stop tacacs+ 为与网络相关的服务需求运行记帐包括SLIP,PPP,PPP NCPs,ARAP等.在进程开始和结束时发通告给TACACS+服务器。 aaa accounting network start-stop tacacs+ 指定Tacacs服务器地址 taca
8、cs-server host 10.111.4.2 在Tacacs+服务器和访问服务器设定共享的关键字,访问服务器和Tacacs+服务器使用这个关键字去加密口令和响应信息。这里使用tac作为关键字。 tacacs-server key tac 访问服务器设置如下: hostname router ! aaa new-model aaa authentication login default tacacs+ aaa authentication login no_tacacs enable aaa authentication ppp default tacacs+ aaa authoriza
9、tion exec tacacs+ aaa authorization network tacacs+ aaa accounting exec start-stop tacacs+ aaa accounting network start-stop tacacs+ enable secret 5 $1$kN4g$CvS4d2.rJzWntCnn/0hvE0 ! interface Ethernet0 ip address 10.111.4.20 255.255.255.0 ! interface Serial0 no ip address shutdown interface Serial1
10、no ip address shutdown ! interface Group-Async1 ip unnumbered Ethernet0 encapsulation ppp async mode interactive peer default ip address pool Cisco2511-Group-142 no cdp enable group-range 1 16 ! ip local pool Cisco2511-Group-142 10.111.4.21 10.111.4.36 tacacs-server host 10.111.4.2 tacacs-server key
11、 tac ! line con 0 exec-timeout 0 0 password cisco login authentication no_tacacs line 1 16 login authentication tacacs modem InOut modem autoconfigure type usr_courier autocommand ppp transport input all stopbits 1 rxspeed 115200 txspeed 115200 flowcontrol hardware line aux 0 transport input all lin
12、e vty 0 4 password cisco ! end 2. DDR(dial-on-demand routing)实例 此例通过Cisco 2500系列路由器的aux端口实现异步拨号DDR连接。Router1拨号连接到Router2。其中采用PPP/CHAP做安全认证,在Router1中应建立一个用户,以对端路由器主机名作为用户名,即用户名应为Router2。同时在Router2中应建立一个用户,以对端路由器主机名作为用户名,即用户名应为Router1。所建的这两用户的password必须相同。 相关命令如下: 任务 命令 设置路由器与modem的接口指令 chat-script sc
13、ript-name EXPECT SEND EXPECT SEND (etc.) 设置端口在挂断前的等待时间 dialer idle-timeout seconds 设置协议地址与电话号码的映射 dialer map protocol next-hop-address name hostname broadcast modem-scriptmodem-regexp system-script system-regexp dial-string 设置电话号码 dialer string dial-string 指定在特定线路下路由器默认 使用的chat-script script dialer|
14、reset script-name Router1: hostname Router1 ! enable secret 5 $1$QKI7$wXjpFqC74vDAyKBUMallw/ ! username Router2 password cisco chat-script cisco-default AT TIMEOUT 30 OK ATDT T TIMEOUT 30 CONNECT c ! interface Ethernet0 ip address 10.0.0.1 255.255.255.0 ! interface Async1 ip address 192.200.10.1 255
15、.255.255.0 encapsulation ppp async default routing async mode dedicated dialer in-band dialer idle-timeout 60 dialer map ip 192.200.10.2 name Router2 modem-script cisco-default 573 dialer-group 1 ppp authentication chap ! ip route 10.0.1.0 255.255.255.0 192.200.10.2 dialer-list 1 protocol ip permit
16、! line con 0 line aux 0 modem InOut modem autoconfigure discovery flowcontrol hardware Router2: hostname Router2 ! enable secret 5 $1$F6EV$5U8puzNt2/o9g.t56PXHo. ! username Router1 password cisco ! interface Ethernet0 ip address 10.0.1.1 255.255.255.0 ! interface Async1 ip address 192.200.10.2 255.2
17、55.255.0 encapsulation ppp async default routing async mode dedicated dialer in-band dialer idle-timeout 60 dialer map ip 192.200.10.1 name Router1 dialer-group 1 ppp authentication chap ! ip route 10.0.0.0 255.255.255.0 192.200.10.1 dialer-list 1 protocol ip permit ! line con 0 line aux 0 modem InO
18、ut modem autoconfigure discovery flowcontrol hardware ! 相关调试命令: debug dialer debug ppp authentication debug ppp error debug ppp negotiation debug ppp packet show dialer 3. 异步拨号备份DDN专线: 此例主连接采用DDN专线,备份线路为电话拨号。当DDN专线连接正常时,主端口S0状态为up,line protocol亦为up,则备份线路状态为standby,line protocol为down,此时所有通信均通过主接口进行。当
19、主接口连接发生故障时,端口状态为down,则激活备份接口,完成数据通信。此方法不适合为X.25做备份。因为,配置封装为X.25的接口只要和X.25交换机之间的连接正常其接口及line protocol的状态亦为 up,它并不考虑其它地方需与之通信的路由器的状态如何,所以若本地路由器状态正常,而对方路由器连接即使发生故障,本地也不会激活备份线路。例4将会描述如何为X.25做拨号备份。 以下是相关命令: 任务 命令 指定主线路改变后,次线路状态发生改变的延迟时间 backup delay enable-delay | never disable-delay | never 指定一个接口作为备份接口
20、 backup interface type number hostname c2522rb ! enable secret 5 $1$J5vn$ceYDe2FwPhrZi6qsIIz6g0 enable password cisco ! username c4700 password 0 cisco ip subnet-zero chat-script cisco-default AT TIMEOUT 30 OK ATDT T TIMEOUT 30 CONNECT c chat-script reset atz ! interface Ethernet0 ip address 16.122.
21、51.254 255.255.255.0 no ip mroute-cache ! interface Serial0 backup delay 10 10 backup interface Serial2 ip address 16.250.123.18 255.255.255.252 no ip mroute-cache no fair-queue ! interface Serial1 no ip address no ip mroute-cache shutdown ! interface Serial2 physical-layer async ip address 16.249.1
22、23.18 255.255.255.252 encapsulation ppp async mode dedicated dialer in-band dialer idle-timeout 60 dialer map ip 16.249.123.17 name c4700 6825179 dialer-group 1 ppp authentication chap ! interface Serial3 no ip address shutdown no cdp enable ! interface Serial4 no ip address shutdown no cdp enable !
23、 interface Serial5 no ip address no ip mroute-cache shutdown ! interface Serial6 no ip address no ip mroute-cache shutdown ! interface Serial7 no ip address no ip mroute-cache shutdown ! interface Serial8 no ip address no ip mroute-cache shutdown ! interface Serial9 no ip address no ip mroute-cache
24、shutdown ! interface BRI0 no ip address no ip mroute-cache shutdown ! router eigrp 200 network 16.0.0.0 ! ip classless ! dialer-list 1 protocol ip permit ! line con 0 line 2 script dialer cisco-default script reset reset modem InOut modem autoconfigure discovery rxspeed 38400 txspeed 38400 flowcontr
25、ol hardware line aux 0 line vty 0 4 password cisco login ! end c2522rb# 4. 异步拨号备份X.25: 设置X.25的拨号备份,首先X.25连接的端口必须运行动态路由协议,异步拨号口必须使用静态路由.本例选择EIGRP作为路由选择协议,将静态路由的Metric的值设置为200,由于EIGRP的默认Metric为90,所以当同时有两条路径通往同一网段时,其中Metric值小的路径生效,而当X.25连接出现问题时,路由器无法通过路由协议学习到路由表,则此时静态路由生效,访问通过拨号端口实现。当X.25连接恢复正常时,路由器又可以
26、学习到路由表,则由于 Metric值的不同,静态路由自动被动态路由所代替,这样就实现了备份的功能。 路由器Router1配置如下: hostname router1 ! enable secret 5 $1$UTvD$99YiY2XsRMxHudcYeHn.Y. enable password cisco ! username router2 password cisco ip subnet-zero chat-script cisco-default AT TIMEOUT 30 OK ATDT T TIMEOUT 30 CONNECT c chat-script reset atz inte
27、rface Ethernet0 ip address 202.96.38.100 255.255.255.0 ! interface Serial0 ip address 202.96.0.1 255.255.255.0 encapsulation x25 x25 address 10112227 x25 htc 16 x25 map ip 202.96.0.2 10112225 broadcast ! interface Serial1 no ip address shutdown ! ! interface Async 1 ip address 202.96.1.1 255.255.255
28、.252 encapsulation ppp dialer in-band dialer idle-timeout 60 dialer map ip 202.96.1.2 name router2 modem-script cisco-default 2113470 dialer-group 1 ppp authentication chap ! router eigrp 200 redistribute connected network 202.96.0.0 ! ip route 202.96.37.0 255.255.255.0 202.96.1.2 200 dialer-list 1 protocol ip
copyright@ 2008-2023 冰点文库 网站版权所有
经营许可证编号:鄂ICP备19020893号-2