1、 The resulting hardware is termed the collector subsystem. This chapter examines the basic optical and thermal considerations that influence receiver design and will emphasize thermal receivers rather than photovoltaic receivers.Also discussed here is an interesting type of concentrator called a com
2、pound parabolic concentrator (CPC). This is a non-imaging concentrator that concentrates light rays that are not necessarily parallel nor aligned with the axis of the concentrator. To complete this section we describe engineering prototype concentrators that have been constructed and tested. Parabol
3、ic concentrators that are not commercial products were chosen for discussion. This allows free discussion without concern for revealing proprietary information. In addition, the prototype concentrators discussed are representative of the parabolic concentrators under development for commercial use,
4、and considerable design information is available.Performance data from some early prototypes are presented. The development includes the following topics: Receiver Designo Receiver Sizeo Receiver Heat Losso Receiver Size Optimization Compound Parabolic Concentrators (CPC) Prototype Parabolic Troughs
5、o Sandia Performance Prototype Trough Prototype Parabolic Disheso Shenandoah Disho JPL PDC1 Other Concentrator Conceptso Fixed-Mirror Solar Collector (FMSC)o Moving Reflector Stationary Receiver (SLATS)o Fixed-Mirror Distributed Focus (FMDF) (spherical bowl) Prototype Performance ComparisonsSpecial
6、note to the reader: The prototype hardware described in the sections below represents the state-of-the-art in the 1970s and early 1980s. For updates on current status of solar concentrator hardware, the reader is referred to the web site of The SunLab (combined efforts of Sandia National Labs and th
7、e National Renewable Energy Laboratory web site: http:/www.energylan.sandia.gov/sunlab/overview.htm and the International Energy Agency web site:/www.solarpaces.org/csp_technology.htm . Readers are also encouraged to access the web sites of different hardware manufacturers.9.1 Receiver DesignThe job
8、 of the receiver is to absorb as much of the concentrated solar flux as possible, and convert it into usable energy (usually thermal energy). Once converted into thermal energy, this heat is transferred into a fluid of some type (liquid or gas), that takes the heat away from the receiver to be used
9、by the specific application.Thus far we have concentrated our attention on reflection of incident solar energy and not been concerned with the geometry of the receiver. There are basically two different types of receivers - the omnidirectional receiver and the focal plane receiver.Rather than deal i
10、n complete generality and talk about the many possible types of receivers that could fall into these two categories, we discuss only two widely used receivers, the linear omnidirectional receiver and the point cavity receiver. This will not artificially limit the applicability of the development of
11、the following paragraphs but will provide a nice focus to the discussion.Figure 9.1 is as photograph of a linear omnidirectional receiver used with parabolic troughs. It consists of a steel tube (usually with a selective coating; see Chapter 8) surrounded by a glass envelope to reduce convection hea
12、t losses. As the name omnidirectional implies, the receiver can accept optical input from any direction.Figure 9.1 Linear omnidirectional receiver, (a) photograph of operational receiver; (b) sketch of receiver assembly cross-section. Courtesy of Sandia National Laboratories.Figure 9.2 is a sketch o
13、f a cavity receiver. This is clearly not an omnidirectional receiver since the light must enter through the cavity aperture (just in front of the inner shield for this receiver) to be absorbed on the cavity walls (coiled tubes in this case).Figure 9.2 Cavity (focal plane) receiver.Typically, the pla
14、ne of the cavity aperture is placed near the focus of the parabola and normal to the axis of the parabola. Thus such a receiver is sometimes called a focal plane receiver. Although the cavity could be linear and thus used with a parabolic trough, a cavity receiver is most commonly used with paraboli
15、c dishes. Figure 9.3 is a photograph of this same parabolic dish cavity receiver.Figure 9.3 Photograph looking into the cavity aperture of the receiver of Figure 9.2. Courtesy of Sandia National Laboratories9.1.1 Receiver SizeOmnidirectional Receivers - The appropriate size for an omnidirectional re
16、ceiver was developed in Chapter 8. The diameter of a tube receiver is r as defined in Equation (8.44) (and 2r1 as shown in Figure 9.1b). A receiver of this size intercepts all reflected radiation within the statistical error limits defined by n. This equation is reproduced here as an aid to the read
17、er. (8.44)where p is the parabolic radius, n the number of standard deviations (i.e. defining the percent of reflected energy intercepted), and tot the weighted standard deviation of the beam spread angle for all concentrator errors, as developed in Section 8.4 and defined by Equation (8.43).As will
18、 be described below, the value of n (i.e. the number of standard deviations of beam spread intercepted by a receiver of size r ), is determined in an optimization process based on balancing the amount of intercepted radiation and amount of heat loss from the receiver. Put in simplified terms, a larg
19、er receiver will capture more reflected solar radiation, but will loose more heat due to radiation and conduction.Cavity Receivers - The appropriate size of the cavity opening (i.e. its aperture) is determined using the same optical principles used in the development of Equation (8.44) but then proj
20、ecting the reflected image onto the focal plane where the receiver aperture will be located.If the beam spread due to errors is small in Figure 9.4, the angles and are approximately 90 degrees. Thus the projection of the image width onto the focal plane is (9.1)Substitution into Equation (8.44) yiel
21、ds (9.2)Figure 9.4 Sizing of cavity aperture considering beam spreading due to errors.Selection of Concentrator Rim Angle - It is interesting to study the impact of receiver type on the preferred concentrator rim angle. The whole idea of a concentrator is to reflect the light energy incident on the
22、collector aperture onto as small a receiver as possible in order to minimize heat loss. Figure 9.5 is a plot of the relative concentration ratios for both cavities and omnidirectional receivers as a function of rim angle. The concentration ratio for the two concepts is the ratio of the collector ape
23、rture area divided by the area of the image at the receiver as defined by Equations (8.44) and (9.2), respectively. Note that the curve for the omnidirectional receiver increases uniformly up to 90 degrees, whereas the curve for the focal plane receiver increases up to a rim angle of about 45 degree
24、s and then decreases because of the cosine term in the denominators in Equations (9.9) and (9.10).Figure 9.5 Variation of geometric concentration ratio with rim angle.The impact of this phenomenon is that most concentrators with an omnidirectional receiver have rim angles near 90 degrees. On the oth
25、er hand, concentrators with focal plane receivers have rim angles near 45 degrees. The curves show only trends for each receiver type, and their magnitude relative to each other as shown in Figure 9.5 is not correct.9.1.2 Receiver Heat LossLinear Omnidirectional Receivers - The heat loss rate from a
26、 linear omnidirectional receiver of the type shown in Figure 9.1 is equal to the heat loss rate from the outside surface of the glass tube. This can be calculated as the sum of the convection to the environment from the glass envelope plus the radiation from the glass envelope to the surroundings.(9
27、.3)where:hg = convective heat-transfer coefficient at outside surface of glassenvelope (W/m2 C)Ag = outside surface of glass envelope (m2)Tg = outside surface temperature of glass envelope (K)Ta = ambient temperature (K)= Stefan-Boltzmann constant (5.6696 10-8 W/m2 K4 )g= emittance of the glassFga = radiation shape factorTs = sky temperature (K) (typically assumed to be 6 Kelvins lower than ambient temperature) (Treadwell, 1976) If all the variables can be eval
copyright@ 2008-2023 冰点文库 网站版权所有
经营许可证编号:鄂ICP备19020893号-2