船舶制造必备英语日常用语句.docx
《船舶制造必备英语日常用语句.docx》由会员分享,可在线阅读,更多相关《船舶制造必备英语日常用语句.docx(39页珍藏版)》请在冰点文库上搜索。
船舶制造必备英语日常用语句
LastupdatedontheafternoonofJanuary3,2021
船舶制造必备英语日常用语句
船舶制造英语日常用语
好东西大家分享啊
船舶制造英语日常用语
一.船体
1.Youmustweldandgrindthisareabeforepainting.
在油漆之前你必须把这个地方电焊修补、打磨好。
2.Thisweldinglineshouldbegougedandweldedagainbeforetightnessinspection.
这条焊缝在密性检查前要碳刨、再焊。
3.Thestructureofthestarboardsideisdifferentfromtheportside.
右舷的结构跟左舷的不一样。
4.Weshouldreinforcethedownsideofthewindlass.
我们应该在锚机的反面加强。
5.Thenavigationdeckisnotplain,
wewillfairthedeckbyhotworking.
驾驶甲板不平,我们要火工校正。
6.Therearetwopiecesofstiffenersandbracketsmustbereplaced.
有两块加强筋和肘板要换新。
7.Twomorefootrestsandhandgripsshouldbeinstalledattheentranceofthesmallhatchcover.
在小舱口盖的进口处再安装两只踏步和拉手。
8.
与No9分段合拢后大接头装配精确性和结构完整性检查。
9.Checkingstructureintegrityofsuperstructure(deckhouse)afterwelding.
上层建筑焊后结构完整性检查。
10.Inspectingfittingaccuracyofhatchcoamingonboard.
货舱口围板船上安装精度检查。
11.Inspectionairpressuretest(withwaterhead)(No15block).
No1压载水舱(分段)气压试验(压头试验)检查。
12.Inspectionhosingtestforupperdeck.
上甲板冲水试验检查。
13.Measuringhull’smaindimensions:
lengthoverall(LOA.),lengthbetweenperpendiculars(LPP.),breathmolded(B.),depthmolded(D.)anddeflectionbeforelaunching.
下水前测量船体主尺度:
总长、两柱间长、型宽、型深、基线挠度。
14.Inspectiondistancebetweendraughtmarksandkeelplateaftermarkingout.
划线后检查吃水标尺至平板龙骨之间的距离。
15.Inspectingfittingaccuracyofdraughtmark(loadinglinemark).
吃水标志(载重线标志)安装精确性检查。
16.Inspectionweldingseamanddimensionofcargohatchcover.
货舱舱口盖焊缝和尺度检查。
二.轮机
1.Inspectionmachiningdimensionofpropellershaft(intermediateshaftorcountershaft).
螺旋桨轴(中间轴)机加工尺寸检查。
2.Checkforsurfacecontactarea(metalliccontact)betweensternshaftandpropellerhubtapers.检查螺旋桨轴与螺旋桨锥度接触面。
3.
Inspectionmachiningdimensionofrudderstock.
舵杆机加工尺寸检查。
4.
Inspectionruddercarrierafterassembly.
上舵承组装后检查。
5.
Inspectionmachiningdimensionofrudderpintle.
舵销机加工尺寸检查。
6.
Inspectionalignmentofstock,rudderbladeandpintle.
舵杆、舵叶、舵销连接后中心线检查。
7.
Loweringtestandtensiontestofanchor.
锚投掷试验和拉力试验。
8.
Measuringdimensionofshaftcouplingboltsandreamerhole.
轴系连接螺栓和钻孔尺寸测量。
9.
Inspectioninstallationcorrectnessofship’snameplate(funnelmark).
船名牌(烟囱标志)安装正确性检查。
10.
Flexibilityandhosingtestforsmallwatertighthatchcover(watertightdoorandwindow).
水密小舱口盖(水密门、窗)启闭灵活性、冲水检查。
11.
Tightnesstest(openingandclosingtest,emergencyopeningandclosingtest)forcargohatchcover.
货舱舱口盖密性试验(启闭试验、应急启闭试验)。
12.
Inspectinganchorthrowingawayappliance.
弃锚装置检查。
13.
Inspectingcenterlinepositioningforshaftsystemandruddersystembeforeboring.
轴、舵系镗孔前中心线定位检查。
14.
Opticalalignedcheckforshaftsystemafterboring.
轴系镗孔后光学校中检查。
15.
艉轴管滑油液压试验。
16.
Measuringdiameterofforeandaftsterntubebearingandbushes.
艉轴管前、后轴承与衬套直径测量。
17.
Inspectionpush-uploadforforeandaftsterntubebushes.
艉轴管前、后衬套压入检查。
18.
Measuringclearancebetweenpropellershaft&bearing.
螺旋桨轴与轴承间隙测量。
19.
Flushingofsterntube.
艉轴管滑油系统的投油清洗。
20.
Inspectingzero(datum)positionofrudderblade.
舵叶0位检查。
21.
Measuringclearanceofrudderjumpingstopper.
舵止跳块的间隙测量。
22.
Inspectingintegrityofsteeringgear.
操舵装置完整性检查。
23.
Measuringinstallationclearanceofrudderbearing.
舵轴承安装间隙测量。
24.
Flushingofpipingsystemforsteeringgear.
舵机管路系统的投油清洗。
25.
Mooringtestofsteeringgear.
舵机系泊试验。
26.
Manoeuvingtestofsteeringgearduringseatrial.
舵机航行中操舵试验。
27.
Emergencymanoeuvingtestofsteeringgear.
舵机应急操舵试验。
28.
Installationandalignmentinspectionofwindlass.
锚机安装与校中检查。
29.
Anchoringandweighingtestofwindlassonseatrial.
锚机航行中抛起锚试验。
30.
Adjustingsafetydeviceforhydraulicsystemofsteeringgear(windlass、mooringwinch).
舵机(锚机、绞缆机)液压系统安全装置调整。
31.
Runningtestandloadingtestfor4tprovisioncrane.
4吨食物吊运转试验和吊重试验。
32.
Loweringandhoistingtestforlifeboat.
救生艇收放试验。
33.
Loadingtestofaccommodationladder(pilotladder).
舷梯(引水员梯)压重试验。
34.
Checkinglinerofmainengine.).
主机垫片检查。
35.
Tighteninginspectionforthroughboltsofmainengine.).
主机贯穿螺栓紧固度检查。
36.
Aligningmainengine’scrankshaftandintermediateshaftafterlaunching.
下水后主机曲轴和中间轴连接后校中。
37.
Aligningintermediateshaftandpropellershaftafterlaunching.
下水后中间轴和螺旋桨连接后校中。
38.
主机动车前(航行试验后)曲轴甩档测量。
39.
Flushinglubricationoil(fueloil)systemofM/E.
主机滑油(燃油)管路投油清洗。
40.
Alignmentinspectioninstallationofshaftgeneratorandgearbox.
?
轴带发电机及齿轮箱安装检查。
41.
AlarmtestingandsafetydevicetestingofM/E.
主机报警和安全装置试验。
42.
Mooringtest(seatrial)ofinspectionattachedpumpsandpipingsystem.
主机系泊(航行)试验并检查其附属泵与管路。
43.
轴带发电机运转试验及主机与轴带发电机之间的离合器的效用试验。
44.
Changeovertestbetweenshaftgeneratoranddieselgeneratoronseatrial.
航行试验中轴带发电机与柴油发电机之间的换车试验。
45.
Overhaulingmainengineafterseatrial.
主机航行试验后的拆检。
46.
Installationinspectionofmaindieselgenerator.
主柴油发电机组安装检查。
47.
Safetydevicetestingforemergencydieselgenerator.
应急柴油发电机的安全装置试验。
48.
Chargingtestandsafetyvalveandautomaticdeviceadjustingformaincompressor(auxiliarycompressor).
主(辅)空气压缩机的充气试验、安全阀和自动装置的调整。
49.
Airtightnesstestandsafetyvalveadjustingformainairreceiver(controlairreceiver,airhornreceiver)onboard.
主空气瓶(控制空气瓶、汽笛空气瓶)装船后气密试验和安全阀的调整。
50.
Safetyvalveadjustingandaccumulatingtestforauxiliaryboiler.
辅锅炉安全阀检验及蓄压试验。
51.
Airtightnesstestforauxiliaryboiler(economizeboiler)onboard.
辅锅炉(废气锅炉)装船后气密试验。
52.
Automaticcontrollertestforauxiliaryboiler.
辅锅炉自动控制装置试验。
53.
Functiontestforeconomizer.
废气锅炉效用试验。
54.
Functiontestandautomaticcontrollertestforballastpump.
压载泵效用试验和自动控制装置试验。
55.
Functiontestofbilgeoilywaterseparator(sewagetreatmentplant,freshwatergenerator,incinerator).
舱底水油水分离器(污水处理装置、制淡装置、焚烧炉)效用试验。
三.
电气
1.
Inspectionmaincableinstallationforwheelhousebeforepanelingdecoration.
敷板前驾驶室检查主干电缆安装.
2.
Measuringinsulationresistanceandreliabilitytestprotectiondeviceformainswitchboard(emergencyswitchboard).
总配电板(应急配电板)绝缘电阻测量和保护装置可靠性试验。
3.
Loadandperformancetestformaingenerator(emergencygenerator).
主发电机(应急发电机)负荷及特性试验。
4.
Automaticgoverningtestofvoltageandfrequencyformaingenerator(emergencygenerator).
主发电机(应急发电机)电压、频率自动调节试验。
5.
Parallel-runningtestformaingenerator.
主发电机并联运行试验。
6.
Dieselgeneratorvoltagecharacteristictest.
柴油发电机电压特性试验。
7.
Dieselgeneratorgovernorsensitivitytest.
柴油发电机调速特性试验。
8.
Testfortakingonafullloadsuddenly.
突加负荷试验。
9.
Reversepowerrelaytriptest.
逆功率脱扣试验。
10.
Over-currentrelaytest.
过电流脱扣试验。
11.
Undervoltagetrippingtest.
低压脱扣试验。
12.
Interlockingreliabilitytest.
联锁试验。
13.
Loadtestforshaftgeneratoranditsfunctiontestonseatrial.
轴带发电机负荷试验和航行时效用试验。
14.
Automaticsupplytestofemergencygenerator.
应急发电机自动供电试验。
15.
Calibratingrudderangleindicator.
舵角指示器校准。
16.
Remotestartingandalarmtestforsteeringgearmotor.
舵机马达遥控起动和报警试验。
17.
Functiontestautomaticpilot.
自动舵效用试验。
18.
Sequencestartingandautomaticexchangeofmotorsforauxiliarymachineandpump.
辅机和泵的电动机程序起动和自动转换。
19.
Chargeanddischargeoperationtestforbatteryandchargeequipment.
蓄电池和充电装置的充放电试验。
20.
Operationtestofemergencyswitching-offdeviceforoilpumpandventilator(bilgepump)inengineroom.
机舱风、油(舱底泵)应急切断装置操作试验。
21.
Remotecontroltestforfirepumpandemergencyfirepump.
消防泵、应急消防泵遥控操作试验。
22.
Functiontestoffoghorn.
雾笛效用试验。
23.
Inspectioninstallationandwatertightnesstransducerofechosounderonberth.
测深仪换能器船台安装和水密性检查。
24.
Functiontestandadjusterrorforlogonseatrial.
航行试验中计程仪效用试验及误差调整。
25.
Functiontestandcalibrationself-heterodynecurvefordirectionfinderonseatrial.
航行试验中测向仪效用试验及自差曲线校正。
26.
Inspectioninstallationforantennaofradioconsoleandmeasuringitsinsulationresistance.
组装报务台天线安装检查和绝缘测量。
27.
Functiontestofradioconsoleonseatrial.
航行试验中组装报务台效用试验。
28.
Calibrationconstanterrorandfunctionforgyro-compassonseatrial.
航行试验中电罗经固定误差校正和效用试验。
29.
Functiontestofradaronseatrial(mooringtest).
航行试验(系泊试验)中雷达效用试验。
30.
Simulating(Automatic)alarmtestforfiredetector.
火警检测器模拟(自动)报警试验。
31.
Theitemsaretestedaccordingtomooringtestprogramasfollowing:
下列项目按系泊试验大纲进行系泊试验:
32.
Functiontestofengineercallingdevice(calldeviceinhospital).
轮机员呼叫(病室呼叫)装置试验。
33.
Functiontestofultra-shortwaveradiotelephone.
超短波对讲机。
34.
Functiontestofremotecontrolsystemofmainengine.
主机遥控系统性能试验。
35.
UMS(unattendedmachineryspace)seatrialcontinue4~6hours.
无人机舱作4~6小时航行试验。
36.
Measuringinsulationresistanceforcircuit.
电路绝缘电阻测量。
37.
Functiontestforweatherfacsimilereceive.
气象传真机效用试验。
四.
上层建筑
1.
A/CductandventductstructureofW/HDeck.
驾驶甲板空调、机械风管结构。
2.
Inspectionthestructureandloadingtestofthelifeboat(Rescueboat)davit.
救生(助)艇吊架结构和压重试验。
3.
.
冷藏氟利昂管系密性试验和真空试验。
4.
.
冷藏机组保护装置试验及打冷试验。
5.
Accommodationair-conditionFreonpipingtobedoneair-tightnessandvacuumtest.
房舱空调氟利昂管系密性试验和真空试验。
6.
Accommodationtobedoneairflowingadjustmenttest.
房舱风量调整试验。
7.
E/CroomPackageA-Ctobedonefunctiontest.
集控室单位式空调效用试验。
8.
E/Rairdriertobedonefunctiontestandalarmtest.
机舱空气干燥器效用试验及报警试验。
9.
Superstructurewater-tightnessdoorsandwindowstobedonehosingtest.
上层建筑水密门窗冲水试验。
10.
Cabinsupplyfantobedonefunctiontest.
房舱风机效用试验。
11.
Superstructurelifesavingandfirefightingequipmenttobedoneinspection.
上层建筑救生、消防设备交验。
12.
Galleyandlaundryequipmenttobedonefunction.
厨房、洗衣间设备交验。
13.
Refrigeratortobedonefunctiontest.
冰箱效用试验。
14.
Rescueboatdavit(liferaftdavit)tobedonestatic(dynamic)loadingtest.
救助艇架(救生筏吊架)静(动)负荷试验。
15.
Mushroomoutletclosingandopeningbyhandtobeinspected.
菌形风帽手动启闭试验。
16.
Superstructurecompressedair(watersupply、firefighting、smokedetection)pipingtobedoneair-tightnesstest.
上层建筑压缩空气管系(供水管、消防管、烟雾探测管)密性试验。
17.
Cabincondensationpipingtobedonefree-flowingtest.
房舱凝水、落水管系畅通试验。
18.
Deckflushingpipingsystemtobedoneair-tightnesstest.
甲板冲洗管系密性试验。
19.
PaintingRM.Firefightingpipetobedoneair-tightnesstest.
油漆间消防管系密性试验。
20.
W/Hwaterspraypipetobedonefunctiontest.
驾驶室水喷淋管系效用试验。
21.
InsulationofA-deck(includingA60insulation).
A甲板绝缘(包括A甲板A60绝缘)。
22.
FloatingfloorofE/CRM.
集控室浮动地板。
23.
Insulationofemergencygeneratorroom(includingA60insulation).
应急发电机室绝缘(包括应急发电机室A60绝缘)。
24.
InsulationofescapeinE/R.(includingA60insulation).
机舱逃口绝缘(包括机舱逃口A60绝缘)。
25.
InsulationofF11#bulkheadinE/R.(includingA60insulation).
F11#舱壁绝缘(包括F11#舱壁A60绝缘)。
26.
Completenessofallcabinstobeinspection.
全船房舱完整性提交。
27.
Inspectioninsulationinstallationfo