modbusRTU的C51单片机程序.docx
《modbusRTU的C51单片机程序.docx》由会员分享，可在线阅读，更多相关《modbusRTU的C51单片机程序.docx（21页珍藏版）》请在冰点文库上搜索。
modbusRTU的C51单片机程序
modbusRTU的C51单片机程序
本文转自：
新势力单片机[url]http:
//www.XinShiL[/url]
modbus.c
#include"main.h"
//字地址0-255（只取低8位）
//位地址0-255（只取低8位）
/*CRC高位字节值表*/
constuint8codeauchCRCHi[]={
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,
0x00,0xC1,0x81,0x40,0x00,0xC1,0x81,0x40,0x01,0xC0,
0x80,0x41,0x01,0xC0,0x80,0x41,0x00,0xC1,0x81,0x40,
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x00,0xC1,
0x81,0x40,0x01,0xC0,0x80,0x41,0x01,0xC0,0x80,0x41,
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x00,0xC1,
0x81,0x40,0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40,0x00,0xC1,0x81,0x40,
0x01,0xC0,0x80,0x41,0x01,0xC0,0x80,0x41,0x00,0xC1,
0x81,0x40,0x01,0xC0,0x80,0x41,0x00,0xC1,0x81,0x40,
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40,0x00,0xC1,0x81,0x40,
0x01,0xC0,0x80,0x41,0x00,0xC1,0x81,0x40,0x01,0xC0,
0x80,0x41,0x01,0xC0,0x80,0x41,0x00,0xC1,0x81,0x40,
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,
0x00,0xC1,0x81,0x40,0x00,0xC1,0x81,0x40,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,
0x01,0xC0,0x80,0x41,0x00,0xC1,0x81,0x40,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40,0x00,0xC1,0x81,0x40,
0x01,0xC0,0x80,0x41,0x01,0xC0,0x80,0x41,0x00,0xC1,
0x81,0x40,0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,
0x00,0xC1,0x81,0x40,0x01,0xC0,0x80,0x41,0x01,0xC0,
0x80,0x41,0x00,0xC1,0x81,0x40
};
/*CRC低位字节值表*/
constuint8codeauchCRCLo[]={
0x00,0xC0,0xC1,0x01,0xC3,0x03,0x02,0xC2,0xC6,0x06,
0x07,0xC7,0x05,0xC5,0xC4,0x04,0xCC,0x0C,0x0D,0xCD,
0x0F,0xCF,0xCE,0x0E,0x0A,0xCA,0xCB,0x0B,0xC9,0x09,
0x08,0xC8,0xD8,0x18,0x19,0xD9,0x1B,0xDB,0xDA,0x1A,
0x1E,0xDE,0xDF,0x1F,0xDD,0x1D,0x1C,0xDC,0x14,0xD4,
0xD5,0x15,0xD7,0x17,0x16,0xD6,0xD2,0x12,0x13,0xD3,
0x11,0xD1,0xD0,0x10,0xF0,0x30,0x31,0xF1,0x33,0xF3,
0xF2,0x32,0x36,0xF6,0xF7,0x37,0xF5,0x35,0x34,0xF4,
0x3C,0xFC,0xFD,0x3D,0xFF,0x3F,0x3E,0xFE,0xFA,0x3A,
0x3B,0xFB,0x39,0xF9,0xF8,0x38,0x28,0xE8,0xE9,0x29,
0xEB,0x2B,0x2A,0xEA,0xEE,0x2E,0x2F,0xEF,0x2D,0xED,
0xEC,0x2C,0xE4,0x24,0x25,0xE5,0x27,0xE7,0xE6,0x26,
0x22,0xE2,0xE3,0x23,0xE1,0x21,0x20,0xE0,0xA0,0x60,
0x61,0xA1,0x63,0xA3,0xA2,0x62,0x66,0xA6,0xA7,0x67,
0xA5,0x65,0x64,0xA4,0x6C,0xAC,0xAD,0x6D,0xAF,0x6F,
0x6E,0xAE,0xAA,0x6A,0x6B,0xAB,0x69,0xA9,0xA8,0x68,
0x78,0xB8,0xB9,0x79,0xBB,0x7B,0x7A,0xBA,0xBE,0x7E,
0x7F,0xBF,0x7D,0xBD,0xBC,0x7C,0xB4,0x74,0x75,0xB5,
0x77,0xB7,0xB6,0x76,0x72,0xB2,0xB3,0x73,0xB1,0x71,
0x70,0xB0,0x50,0x90,0x91,0x51,0x93,0x53,0x52,0x92,
0x96,0x56,0x57,0x97,0x55,0x95,0x94,0x54,0x9C,0x5C,
0x5D,0x9D,0x5F,0x9F,0x9E,0x5E,0x5A,0x9A,0x9B,0x5B,
0x99,0x59,0x58,0x98,0x88,0x48,0x49,0x89,0x4B,0x8B,
0x8A,0x4A,0x4E,0x8E,0x8F,0x4F,0x8D,0x4D,0x4C,0x8C,
0x44,0x84,0x85,0x45,0x87,0x47,0x46,0x86,0x82,0x42,
0x43,0x83,0x41,0x81,0x80,0x40
};
uint8testCoil;//用于测试位地址1
uint16testRegister;//用于测试字址址16
uint8localAddr=1;//单片机控制板的地址
uint8sendCount;//发送字节个数
uint8receCount;//接收到的字节个数
uint8sendPosi;//发送位置
uint16crc16（uint8*puchMsg,uint16usDataLen）
{
uint8uchCRCHi=0xFF;/*高CRC字节初始化*/
uint8uchCRCLo=0xFF;/*低CRC字节初始化*/
uint32uIndex;/*CRC循环中的索引*/
while（usDataLen--）/*传输消息缓冲区*/
{
uIndex=uchCRCHi^*puchMsg++;/*计算CRC*/
uchCRCHi=uchCRCLo^auchCRCHi[uIndex];
uchCRCLo=auchCRCLo[uIndex];
}
return（uchCRCHi<<8|uchCRCLo）;
}//uint16crc16（uint8*puchMsg,uint16usDataLen）
//开始发送
voidbeginSend（void）
{
b485Send=1;//设为发送
sendPosi=0;
if（sendCount>1）
sendCount--;
ACC=sendBuf[0];
TB8=P;
SBUF=sendBuf[0];
}//voidbeginSend（void）
//读线圈状态
voidreadCoil（void）
{
uint8addr;
uint8tempAddr;
uint8byteCount;
uint8bitCount;
uint16crcData;
uint8position;
uint8i,k;
uint8result;
uint16tempData;
uint8exit=0;
//addr=（receBuf[2]<<8）+receBuf[3];
//tempAddr=addr&0xfff;
addr=receBuf[3];
tempAddr=addr;
//bitCount=（receBuf[4]<<8）+receBuf[5];//读取的位个数
bitCount=receBuf[5];
byteCount=bitCount/8;//字节个数
if（bitCount%8!
=0）
byteCount++;
for（k=0;k{//字节位置
position=k+3;
sendBuf[position]=0;
for（i=0;i<8;i++）
{
getCoilVal（tempAddr,&tempData）;
sendBuf[position]|=tempData<tempAddr++;
if（tempAddr>=addr+bitCount）
{//读完
exit=1;
break;
}
}
if（exit==1）
break;
}
sendBuf[0]=localAddr;
sendBuf[1]=0x01;
sendBuf[2]=byteCount;
byteCount+=3;
crcData=crc16（sendBuf,byteCount）;
sendBuf[byteCount]=crcData>>8;
byteCount++;
sendBuf[byteCount]=crcData&0xff;
sendCount=byteCount+1;
beginSend（）;
}//voidreadCoil（void）
//读寄存器
voidreadRegisters（void）
{
uint8addr;
uint8tempAddr;
uint16result;
uint16crcData;
uint8readCount;
uint8byteCount;
uint8finsh;//1完成0出错
uint16i;
uint16tempData=0;
//addr=（receBuf[2]<<8）+receBuf[3];
//tempAddr=addr&0xfff;
addr=receBuf[3];
tempAddr=addr;
//readCount=（receBuf[4]<<8）+receBuf[5];//要读的个数
readCount=receBuf[5];
byteCount=readCount*2;
for（i=0;i{
getRegisterVal（tempAddr,&tempData）;
sendBuf[i+3]=tempData>>8;
sendBuf[i+4]=tempData&0xff;
}
sendBuf[0]=localAddr;
sendBuf[1]=3;
sendBuf[2]=byteCount;
byteCount+=3;
crcData=crc16（sendBuf,byteCount）;
sendBuf[byteCount]=crcData>>8;
byteCount++;
sendBuf[byteCount]=crcData&0xff;
sendCount=byteCount+1;
beginSend（）;
}//voidreadRegisters（void）
//强制单个线圈
voidforceSingleCoil（void）
{
uint8addr;
uint8tempAddr;
uint16tempData;
uint8onOff;
uint8i;
//addr=（receBuf[2]<<8）+receBuf[3];
//tempAddr=addr&0xfff;
addr=receBuf[3];
tempAddr=addr;
//onOff=（receBuf[4]<<8）+receBuf[5];
onOff=receBuf[4];
//if（onOff==0xff00）
if（onOff==0xff）
{//设为ON
tempData=1;
}
//elseif（onOff==0x0000）
elseif（onOff==0x00）
{//设为OFF
tempData=0;
}
setCoilVal（tempAddr,tempData）;
for（i=0;i{
sendBuf=receBuf;
}
sendCount=receCount;
beginSend（）;
}//voidforceSingleCoil（void）
//设置多个寄存器
voidpresetMultipleRegisters（void）
{
uint8addr;
uint8tempAddr;
uint8byteCount;
uint8setCount;
uint16crcData;
uint16tempData;
uint8finsh;//为1时完成为0时出错
uint8i;
//addr=（receBuf[2]<<8）+receBuf[3];
//tempAddr=addr&0xfff;
addr=receBuf[3];
tempAddr=addr&0xff;
//setCount=（receBuf[4]<<8）+receBuf[5];
setCount=receBuf[5];
byteCount=receBuf[6];
for（i=0;i{
tempData=（receBuf[i*2+7]<<8）+receBuf[i*2+8];
setRegisterVal（tempAddr,tempData）;
}
sendBuf[0]=localAddr;
sendBuf[1]=16;
sendBuf[2]=addr>>8;
sendBuf[3]=addr&0xff;
sendBuf[4]=setCount>>8;
sendBuf[5]=setCount&0xff;
crcData=crc16（sendBuf,6）;
sendBuf[6]=crcData>>8;
sendBuf[7]=crcData&0xff;
sendCount=8;
beginSend（）;
}//voidpresetMultipleRegisters（void）
//检查uart0数据
voidcheckComm0Modbus（void）
{
uint16crcData;
uint16tempData;
if（receCount>4）
{
switch（receBuf[1]）
{
case1:
//读取线圈状态（读取点16位以内）
case3:
//读取保持寄存器（一个或多个）
case5:
//强制单个线圈
case6:
//设置单个寄存器
if（receCount>=8）
{//接收完成一组数据
//应该关闭接收中断
if（receBuf[0]==localAddr&&checkoutError==0）
{
crcData=crc16（receBuf,6）;
if（crcData==receBuf[7]+（receBuf[6]<<8））
{//校验正确
if（receBuf[1]==1）
{//读取线圈状态（读取点16位以内）
readCoil（）;
}
elseif（receBuf[1]==3）
{//读取保持寄存器（一个或多个）
readRegisters（）;
}
elseif（receBuf[1]==5）
{//强制单个线圈
forceSingleCoil（）;
}
elseif（receBuf[1]==6）
{
//presetSingleRegister（）;
}
}
}
receCount=0;
checkoutError=0;
}
break;
case15:
//设置多个线圈
tempData=receBuf[6];
tempData+=9;//数据个数
if（receCount>=tempData）
{
if（receBuf[0]==localAddr&&checkoutError==0）
{
crcData=crc16（receBuf,tempData-2）;
if（crcData==（receBuf[tempData-2]<<8）+receBuf[tempData-1]）
{
//forceMultipleCoils（）;
}
}
receCount=0;
checkoutError=0;
}
break;
case16:
//设置多个寄存器
tempData=（receBuf[4]<<8）+receBuf[5];
tempData=tempData*2;//数据个数
tempData+=9;
if（receCount>=tempData）
{
if（receBuf[0]==localAddr&&checkoutError==0）
{
crcData=crc16（receBuf,tempData-2）;
if（crcData==（receBuf[tempData-2]<<8）+receBuf[tempData-1]）
{
presetMultipleRegisters（）;
}
}
receCount=0;
checkoutError=0;
}
break;
default:
break;
}
}
}//voidcheckComm0（void）
//取线圈状态返回0表示成功
uint16getCoilVal（uint16addr,uint16*tempData）
{
uint16result=0;
uint16tempAddr;
tempAddr=addr&0xfff;
//只取低8位地址
switch（tempAddr&0xff）
{
case0:
break;
case1:
*tempData=testCoil;
break;
case2:
break;
case3:
break;
case4:
break;
case5:
break;
case6:
break;
case7:
break;
case8:
break;
case9:
break;
case10:
break;
case11:
break;
case12:
break;
case13:
break;
case14:
break;
case15:
break;
case16:
break;
default:
break;
}
returnresult;
}//uint16getCoilVal（uint16addr,uint16*data）
//设定线圈状态返回0表示成功
uint16setCoilVal（uint16addr,uint16tempData）
{
uint16result=0;
uint16tempAddr;
tempAddr=addr&0xfff;
switch（tempAddr&0xff）
{
case0:
break;
case1:
testCoil=tempData;
break;
case2:
break;
case3:
break;
case
升级会员 