传感器双语实验报告1.docx
《传感器双语实验报告1.docx》由会员分享,可在线阅读,更多相关《传感器双语实验报告1.docx(21页珍藏版)》请在冰点文库上搜索。
传感器双语实验报告1
QR7611—A
编号:
SYB-2016-2
Report No.:
SYB-2016-2
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
试验报告
Testreport
编制(Preparedby)
审核(Auditedby)
批准(Approvedby)
XXXXXXXXX有限公司实验室
ChengduchangdiSensingtechnologylimitedcompanylaboratory
二〇一六年二月三日
Februarythe third,twothousand and sixteen
检验报告Testreport
生产单位
Productionunit
XXXXXXX有限公司
XXXXXXXXXSensingtechnologylimitedcompany
规格图号
Product model
XXXXXXX
产品名称Productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
生产日期
Productiondate
2016.01.15
样品数量
Samplequantity
15件15pieces
送样日期
Datelanded
2016.01.18
试验日期Testingperiod
2016.1.19~2016.2.1
送样者
Deliverer
管爱AihuaGuan
试验项目
Testitemes
1、基本性能Basicperformance
2、湿热试验Cyclicdampheattest
3、盐雾试验Saltspraytest
4、高低温冲击试验Lightandlowtemperatureimpacttest
5、耐汽油试验Gasolineresistanttest
6、高温试验High-temperaturetest
7、低温试验Low-temperaturetest
8、振动试验Vibrationtest
9、绝缘耐压试验Dielectricstrengthtest
10、防水试验Waterprooftest
试验依据
Teststandard
Q/CD·J37-2011CDS006C轮速传感器技术条CDS006CWheelspeedsensortechnicalcondition
GB/T2423.4-2008电工电子产品基本环境试验规程试验Db:
交变湿热试验方法
Environmentaltestingforelectricandelectronicproducts-Part2:
Testmethod-TestDb:
Dampheat,cyclic
GB/T2423.10-2008电工电子产品环境试验第2部分:
试验方法Testmethod试验FC和导则:
振动Environmentaltestingforelectricandelectronicproducts-Part2:
Testsmethods-TestFc:
Vibration(sinusoidal)
GB/T2423.17-2008电工电子产品基本环境试验规程试验Ka:
盐雾试验方法TestmethodBasicenvironmentaltestingproceduresforelectricandelectronicproducts--TestKa:
Saltmist
GB/T2423.22-2012电工电子产品基本环境试验规程试验N:
温度变化试验方法
Environmentaltesting-Part2:
Testsmethods-TestN:
Changeoftemperature
试验结论Judgemen
依据产品图样及上述标准分组对样品进行各项试验,产品性能均满足要求(具体试验数据见单项试验报告),故判该产品性能合格。
Accordingtoproductdesigndrawingsandstandardmentionedabovetohaveeachtest,productperformancerequirementsshouldmeetrequirements(seeeachtestdatasforindividualtestreports),Sodeterminedthe samplesis qualified forperformance.
备注Note
15件试件分为3组,每组5件,分别进行相应试验。
Divide15specimensintothreegroups,eachgrouphavefivesamples,thesegroupscarriedoutthecorrespondingexperimentsrespectively.
检验报告Testreport
产品名称Productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
规格图号
Product model.
XXXXXXX
XXXXXXX
XXXXXXX
试件数量samplequantity
15件5pieces
试验日期
Testingperiod
2016.1.19
试验项目
Testitemes
基本性能Basicperformance
试验目的
testpurpose
验证产品的基本性能是否满足要求。
Theaimofexperimentistofindoutwhetherthebasicpropertiesoftheproductsmeettherequirements.
试验依据
Teststandard
XXXXXXX
试验方法
Testmethod
传感器电阻:
将数字三用表调零,从传感器两插头端子测量线圈电阻。
传感器输出信号峰—峰值:
将产品用专用测试工装安装在传感器试验台上,用塞尺调整传感头与齿圈凸齿间隙至0.7mm,在传感器输出端接1MΩ电阻;开动传感器试验台,根据测试频率调整试验台转速,用示波器在1MΩ电阻两端检测Vpp值。
Sensorresistance:
switchtheAVOmeterto0zero,measurethecoilresistancefromthetwo pinsterminal ofthewheelspeedsensor。
Thepeak-peakvoltageofoutputsignalofthewheelspeedsensor:
MakeuseofSpecialEquipmenttoinstalltheproductsontothewheelspeedsensorTest-bed.ajustthegapbetweensensingheadandgearringto0.7mm,andconnecta1MΩresistancewithoutputtheterminalofsensors;thenstartwheelspeedsensorTest-bedandadjustthespeedofTest-bedin accordance withtestingfrequency,makeuseofoscilloscopetomeasuretheVppvaluefrom1MΩresistance’stwoends.
技术要求Technicalrequirement
电阻(20℃)Resistance(20℃)
R=1150+100-50Ω
信号电压峰-峰值Thepeak-peaksignalvoltage
Vpp≥0.11V(100Hz齿隙GAP0.7mm)
实测结果
Testresult
1#
1169
11#
1176
1#
1.28
11#
1.02
2#
1176
12#
1165
2#
1.20
12#
1.42
3#
1162
13#
1166
3#
1.36
13#
1.22
4#
1170
14#
1169
4#
1.44
14#
1.32
5#
1163
15#
1165
5#
1.20
15#
1.26
6#
1172
6#
1.28
7#
1163
7#
1.36
8#
1164
8#
1.20
9#
1166
9#
1.18
10#
1164
10#
1.38
试验结论
Judgemen
产品基本性能合格。
Thebasicperformanceofproductsmeetrequirements.
检验报告Testreport
产品名称Productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
规格图号
Product model
XXXXXXX
XXXXXXX
XXXXXXX
试件数量Samplequantity
5件5pieces
试验日期Testingperiod
2016.1.19~2016.1.26
试验项目
Testitemes
交变湿热试验Cyclicdampheattest
试验目的
Testpurpose
验证产品的交变湿热性能是否满足要求。
Theaimofexperimentistofindoutwhetherthecyclicdampheatpropertiesoftheproductsmeettherequirements.
试验依据
Teststandard
GB/T2423.4-2008电工电子产品环境试验试验Db:
交变湿热试验方法
GB/T2423.4-2008Environmentaltestingforelectricandelectronicproducts-Part2:
Testmethod-TestDb:
Dampheat,cyclic
试验方法
Testmethod
按GB/T2423.4-2008进行试验。
传感器插头按工作状态安装,引出测试导线。
高温温度:
40℃,试验周期:
6d。
产品在不工作状态下试验。
试验后检测产品基本电气性能。
InaccordancewiththeGB/T2423.4-2008,sensorplugsshallbeanormalworkingcondition. Pulltestleadsout.HighTemperatureTemperature:
40℃,testcycle:
6d.Productstestedinthenon-operatingstate.Checkbasicelectricalperformanceoftheproducts。
技术要求Technicalrequirement
产品基本电气性能满足要求Thebasicperformanceofproductsshouldmeetrequirements.
电阻(20℃)Resistance(20℃)
R=1150+100-50Ω
信号电压峰-峰值Thepeak-peaksignalvoltage
Vpp≥0.11V(100Hz齿隙GAP0.7mm)
实测结果Testresult
1#
1168
1.28
2#
1176
1.22
3#
1160
1.36
4#
1170
1.42
5#
1163
1.20
试验结论Judgemen
产品交变湿热性能合格。
Thecyclicdampheaperformanceofproductsmeetrequirements.
检验报告Testreport
产品名称Productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
规格图号
Product model
XXXXXXX
XXXXXXX
XXXXXXX
试件数量Samplequantity
5件5pieces
试验日期Testingperiod
2016.1.21~2016.1.26
试验项目
Testitemes
盐雾试验Saltspraytest
试验目的
Testpurpose
验证产品的耐盐雾性能是否满足要求。
Theaimofexperimentistofindoutwhetherthesaltspraylpropertiesoftheproductsmeettherequirements.
试验依据
Teststandard
GB/T2423.17-2008电工电子产品基本环境试验规程试验Ka:
盐雾试验方法
GB/T2423.17-2008TestmethodBasicenvironmentaltestingproceduresforelectricandelectronicproducts--TestKa:
Saltmist
试验方法
Testmethod
试验方法按GB/T2423.17。
试验前按产品标准做出厂试验项目检查。
产品在试验箱内应处于正常安装状态。
试验时间持续96小时。
试验后将表面擦拭干净后测试基本电气性能和腐蚀面积。
InaccordancewiththeGB/T2423.17,according toproductstandardtocompletefactoryinspectionitemsbeforethetest.Productsinthetestchambershallbeanormalworkingcondition.Testlasted96hours.Wipecleanthesurfaceofproductsaftertest,atlastCheckproduct’sbasicelectricalperformanceandcorrosionarea.
技术要求Technicalrequirement
外壳经96小时盐雾试验无腐蚀,产品基本电气性能应满足要求Shellsshouldbenocorrosionafter96hoursofsaltspray test,andbasicelectricalpropertiesoftheproductshouldmeettherequirements
外壳无腐蚀
Shellsnocorrosion
电阻(20℃)Resistance(20℃)
R=1150+100-50Ω
信号电压峰-峰值Thepeak-peaksignalvoltage
Vpp≥0.11V(100Hz齿隙GAP0.7mm)
实测结果Testresult
11#
无腐蚀Nocorrosion
1176
1.00
12#
无腐蚀Nocorrosion
1165
1.42
13#
无腐蚀Nocorrosion
1166
1.22
14#
无腐蚀Nocorrosion
1168
1.32
15#
无腐蚀Nocorrosion
1165
1.24
试验结论Judgemen
产品耐盐雾性能合格。
Thesaltspraylperformanceofproductsmeetrequirements.
检验报告Testreport
产品名称Productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
规格图号
Product model
XXXXXXX
XXXXXXX
XXXXXXX
试件数量Samplequantity
5件5pieces
试验日期Testingperiod
2016.1.27
试验项目
Testitemes
高低温冲击试验Lightandlowtemperatureimpacttest
试验目的
Testpurpose
验证产品的耐高低温冲击性能是否满足要求。
Theaimofexperimentistofindoutwhetherthelightandlowtemperatureimpactpropertiesoftheproductsmeettherequirements.
试验依据
Teststandard
XXXXXX
试验方法
Testmethod
将产品直接放入温度已降至-40℃的低温箱中,30min后取出,在不超过10s内放入温度已升至125℃的高温箱中,30min后取出,在不超过10s内放入-40℃的低温箱中。
上述过程构成一循环,产品试验5个循环。
试验完成后,产品置于试验室温度条件下到温度稳定后检查产品基本电气性能。
Placetheunitinacryostatthatthetemperaturehavealreadyloweredto-40℃,taketheunitoutafter30mins,within10s,placetheminahigh-temperaturecabinetthatthetemperaturehavealreadyrisedto125℃,within10s,taketheunitoutafter30mins,repeatthisprocess5times.afterthetest,placetheunitintestrometemperatureconditions,andCheckproduct’sbasicelectricalperformanceuntilit’stemperaturestabilized.
技术要求Technicalrequirement
产品基本电气性能满足要求Thebasicperformanceofproductsshouldmeetrequirements.
电阻(20℃)Resistance(20℃)
R=1150+100-50Ω
信号电压峰-峰值Thepeak-peaksignalvoltage
Vpp≥0.11V(100Hz齿隙GAP0.7mm)
实测结果Testresult
1#
1170
1.26
2#
1176
1.20
3#
1162
1.38
4#
1171
1.44
5#
1163
1.20
试验结论Judgemen
产品耐高低温冲击性能合格。
Thelightandlowtemperatureimpactperformanceofproductsmeetrequirements.
检验报告Testreport
产品名称Productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
规格图号
Product model
XXXXXXX
XXXXXXX
XXXXXXX
试件数量Samplequantity
5件5pieces
试验日期Testingperiod
2016.1.28
试验项目
Testitemes
高温试验High-temperaturetest
试验目的
Testpurpose
验证产品的高温性能是否满足要求。
Theaimofexperimentistofindoutwhetherthehigh-temperaturelpropertiesoftheproductsmeettherequirements.
试验依据
Teststandard
XXXXXX
试验方法
Testmethod
将产品放入从室温开始的高温箱中,达到200±3℃保持2h后取出,测试产品基本电气性能。
Placetheunitinahigh-temperaturecabinet, whichStartatroomtemperature,taketheunitoutaftertheirtemperatureri`sedto200±3℃and lastedfor 2h,Checkproduct’sbasicelectricalperformanceafterthetest
技术要求Technicalrequirement
高温试验后产品基本电气性能满足要求Thebasicperformanceofproductsshouldmeetrequirementsafterhigh-temperatureltest.
电阻(20℃)Resistance(20℃)
R=1150+100-50Ω
信号电压峰-峰值Thepeak-peaksignalvoltage
Vpp≥0.11V(100Hz齿隙GAP0.7mm)
实测结果
Testresult
1#
1169
1.26
2#
1177
1.20
3#
1162
1.34
4#
1169
1.44
5#
1163
1.22
试验结论Judgemen
产品高温性能合格。
Thehigh-temperaturelperformanceofproductsmeetrequirements.
检验报告Testreport
产品名称productname
鼓式气制动轮速传感器
Drumbrakewheelspeedsensors
规格图号
Product model
XXXXXXX
XXXXXXX
XXXXXXX
试件数量Samplequantity
5件5pieces
试验日期Testingperiod
2016.1.28
试验项目
Testitemes
低温试验Low-temper