交大方菱数控平面切割控制系统F2300Ver23操作手册.docx

交大方菱数控平面切割控制系统F2300Ver23操作手册.docx

《交大方菱数控平面切割控制系统F2300Ver23操作手册.docx》由会员分享，可在线阅读，更多相关《交大方菱数控平面切割控制系统F2300Ver23操作手册.docx（10页珍藏版）》请在冰点文库上搜索。

交大方菱数控平面切割控制系统F2300Ver23操作手册

交大方菱数控平面切割控制系统F2300_Ver23_操作手册

F2300型数控切割控制系统使用说明书方菱数控切割机控制系统使用手册（Ver.2.3）（型号：

F2300）上海交亿数控设备有限公司2022-12i

F2300型数控切割控制系统使用说明书目录F2300型数控切割机控制系统使用手册（VER.2.2）.......................................................................I 阅读手册..............................................................................................................................................II 环境要求..............................................................................................................................................II 维护......................................................................................................................................................II 高压电..................................................................................................................................................II 注意事项..................................................................................................................................................1 开机关机..............................................................................................................................................1 备份参数..............................................................................................................................................2 还原参数..............................................................................................................................................2 清空代码..............................................................................................................................................2 系统升级..............................................................................................................................................3 优盘工作不正常..................................................................................................................................3 断电恢复..............................................................................................................................................3 第一章概述............................................................................................................................................4 1.1系统简介.......................................................................................................................................4 1.2系统特点.......................................................................................................................................4 1.3技术指标.......................................................................................................................................5 1.4系统接口.......................................................................................................................................5 1.5硬件配置.......................................................................................................................................5 第二章系统开机....................................................................................................................................6 2.1系统操作面板说明.......................................................................................................................6 2.2系统启运及主界面说明...............................................................................................................6 2.3主界面功能索引...........................................................................................................................9 第三章自动功能..................................................................................................................................10 3.1自动操作索引.............................................................................................................................11 3.2调速.............................................................................................................................................12 3.2.1正常调速............................................................................................................................12 3.2.2快速调速............................................................................................................................12 3.3空走功能.....................................................................................................................................12 3.4后退功能/透枪功能.....................................................................................................................12 3.5边缘切割/偏移切割/返回...........................................................................................................12 3.6图形功能.....................................................................................................................................13 3.7选行/选号....................................................................................................................................14 3.8镜像.............................................................................................................................................16 3.9图形旋转/钢板校正....................................................................................................................18 3.10排列...........................................................................................................................................22 3.11比例...........................................................................................................................................26 3.12图形还原...................................................................................................................................26 iii

F2300型数控切割控制系统使用说明书3.13图形放大/缩小..........................................................................................................................26 3.14回参功能...................................................................................................................................27 3.15退出切割....................................................................................................................................27 3.16断电恢复....................................................................................................................................27 第四章手动功能..................................................................................................................................29 4.1点动功能.....................................................................................................................................29 4.2连动功能.....................................................................................................................................30 第五章代码说明..................................................................................................................................31 5.1编程符号及说明........................................................................................................................31 5.2坐标系统....................................................................................................................................31 5.3G代码说明................................................................................................................................32 5.4M代码说明...............................................................................................................................37 第六章文件操作..................................................................................................................................38 6.1代码操作索引.............................................................................................................................39 6.2本机代码....................................................................................................................................39 6.2.1调入代码.............................................................................................................................39 6.2.2删除代码.............................................................................................................................41 6.2.3单拷文件.............................................................................................................................42 6.2.4全拷文件.............................................................................................................................42 6.3U盘文件....................................................................................................................................43 6.4新建代码....................................................................................................................................44 6.5代码编辑....................................................................................................................................44 6.6编译代码....................................................................................................................................45 第七章参数设置..................................................................................................................................46 7.1常用参数....................................................................................................................................46 7.2氧燃气参数................................................................................................................................47 7.4等离子参数................................................................................................................................48 7.5喷粉参数....................................................................................................................................49 7.6系统参数....................................................................................................................................50 7.7保存参数....................................................................................................................................52 第八章诊断功能..................................................................................................................................53 8.1诊断界面索引..............................................................................