华为MA5626配置成普通交换机的完整方法Word文档格式.docx
《华为MA5626配置成普通交换机的完整方法Word文档格式.docx》由会员分享,可在线阅读,更多相关《华为MA5626配置成普通交换机的完整方法Word文档格式.docx(12页珍藏版)》请在冰点文库上搜索。
enable
config
portmode0/0/1ge
portmode0/0/2ge指定1,2光口为GE模式。
然后把业务口透传到光口,真要命,找好久还搞明白。
vlanservice-profileprofile-id1
user-bridgingenable用户桥接使能
commit加载
quit
vlan4000smart定义业务vlan
定义管理vlan
vlanbindservice-profile4000profile-id1将vlan邦定1号模板
multi-service-portvlan4000port0/11-8user-vlanuntaggedrx-cttr6tx-cttr6批量加载业务口
interfacevlanif4000带内管理vlan
ipaddress111.111.111.1255.255.255.0带内管理ip地址
portvlan40000/01ETH口vlan1透传到上行口1
portvlan40000/02ETH口vlan1透传到上行口2
save
rebootsystem
MA5626(config)#undo
service-port
all
MA5626(config)#interface
eth
0/1
MA5626(config-if-eth-0/1)#traffic-suppress
all
unicast
value
1
broadcast
MA5626(config-if-eth-0/1)#quit
MA5626(config)#multi-service-port
vlan
transparent
board
1
other-all
rx-cttr
6
tx-cttr
6
确实要批量增加业务虚端口?
(y/n)[n]:
y
本次批增操作涉及业务单板总数:
本次批增操作涉及业务虚端口总数:
24
批量增加开始......
批量增加结束:
本次批增需要增加业务虚端口总数:
其中,
增加成功总数:
MA5626(config)#save
data
数据正在保存,请稍候...
开端口直通:
通过串口线用超级终端登录
用户名root
密码mduadmin
enable打开交换机
MA5626#config进入配置模式
MA5626(config)#vlanservice-profileprofile-id1创建一个ID为1的VLAN
{<
cr>
|profile-name<
K>
}:
回车
Command:
Vlanservice-profileprofile-id1
:
user-bridgingenable启用用户桥接
Info:
Pleaseusethecommitcommandtomakemodificationstakeeffect
#commit
commit
vlanbindservice-profile1profile-id1
multi-service-portvlan1port0/11-8user-vlanuntaggedrx-cttr6tx-cttr6
在敲一遍:
multi-service-portvlan1port0/11-15user-vlanuntaggedrx-cttr6tx-cttr6
以上配好就可以当交换机去用了。
附图:
如果出现的是1515,则需要再敲一遍该命令。
硬件连接方式
首先连接电脑与onu,通过配置线连接
图为配置线,“网线头”插入onu的CONSOLE口,另一端与电脑的串口接。
图为onu上对应的CONSOLE接口(插入“网线头”即可)
电脑端操作
首先打开超级终端:
开始—程序—附件---通信—超级终端
打开超级中断后出现如下提示
点否进入如下界面
名称随便写,图标选择默认的即可,然后点击确定出现如下界面
连接口选择COM1或者COM2根据自己的机器选择,1不行就2,点击确定,然后按照下图设置
点击确定
然后到文件—属性—设置中按下图方式
一定要设置ASCII码
按照图中行延迟和字符延迟都设置为200毫秒,然后点击确定即可
在超级终端出点击回车即可出现要求输入用户名和密码
华为onu登陆用户名root
密码mduadmin
登陆后界面如下
Board'
sLANIPaddressis10.11.104.2
之前在我这买过的,加10元远程帮你调成千兆交换机。
请qq联系我!
673395357
华为MA5626配置成普通交换机的方法
本文以16口MA5626为例
MA5626#config
MA5626(config)#vlanservice-profileprofile-id1
user-bridgingenable
Command:
vlanservice-profileprofile-id1
MA5626(config-vlan-srvprof-1)#user-bridgingenable
Info:
Pleaseusethecommitcommandtomakemodificationstakeeffect
MA5626(config-vlan-srvprof-1)#commit
MA5626(config-vlan-srvprof-1)#quit
MA5626(config)#vlanbindservice-profile1profile-id1
MA5626(config)#multi-service-portvlan1port0/11-8user-vlanuntaggedrx-cttr6tx-cttr6
Itwilltakeseveralminutes,andconsolemaytimeout,pleaseusecommand
idle-timeouttosettimelimit
Areyousuretocreateservicevirtualport(s)?
(y/n)[n]:
Thenumberoftotalboardinthisoperation:
1
Thenumberoftotalservicevirtualportinthisoperation:
8
Creatingstart...
Creatingend:
Thenumberoftotalservicevirtualportwhichneedbecreated:
Thenumberoftotalservicevirtualportwhichhavebeencreated:
MA5626(config)#save
|configuration<
|data<
save